Woodworking Forum

  1. Home
  2. Woodworking Forum
51629 Threads Posts
to

Worth reading in Woodworking Forum

Horrible closet dimensions. Suggestions?

As a new homeowner I've realized I'm hooked on making home improvements. I am definitely a newbie, although from the lo...
26 comments posted 20yrs
posted by krystek
26 comments posted 20yrs posted by krystek

aquarium stand

looking for plans for an aquarium stand 55 gal.
27 comments posted 20yrs
posted by puzzle
27 comments posted 20yrs posted by puzzle

Wood fill in 100 y/o+ trim/doors

I am currently restoring all the (looks/smells like) pine trim/doors in my 103 y/o house. I'm sure this question has be...
0 comments posted 20yrs
posted by baboon
0 comments posted 20yrs posted by baboon

Refinish butcherblock table question

I've got a good oak butcherblock dining table I want to refinish. Is there anything special to avoid, or do, with butch...
2 comments posted 20yrs
posted by JAntero45
2 comments posted 20yrs posted by JAntero45

FINISHING RED OAK, TUNG OIL AND WAX?

OK - first project finished. In Red oak. Applied two coats tung oil and it looks good. Been advised to wax it now with...
7 comments posted 20yrs
posted by mike
7 comments posted 20yrs posted by mike

screw thread pitch

I see wood screws such as pocket hole screws available in coarse and fine thread. Where should each be used?
1 comments posted 20yrs
posted by mark
1 comments posted 20yrs posted by mark

Circular saw blade tip grinds

What tip grind should be used where. I see flat, combination, ATB alternate tip bevel, ... What should I use for 1.solid...
4 comments posted 20yrs
posted by mark
4 comments posted 20yrs posted by mark

raised panels

From what I understand verticle panel raising is easier and safer than doing it with a large 3+" horizontal panel raisi...
14 comments posted 20yrs
posted by mark
14 comments posted 20yrs posted by mark

Rough sawing logs with a chainsaw?

I've got some trees, pines particularly, that I'd like to slab for an outbuilding. I understand there's a ripping blade...
8 comments posted 20yrs
posted by tomnie
8 comments posted 20yrs posted by tomnie

Fleshing Board for scraping pelts

I've got a guy wants a curved fleshing board like this - http://www.mntrappers.com/beams.htmlI'm going to go with popla...
4 comments posted 20yrs
posted by JayPique
4 comments posted 20yrs posted by JayPique

Woodworking Show, KC

As usual it was crowded but this time no waiting outside into the convention Center in 115 St. Most people buy their ti...
0 comments posted 20yrs
posted by kenh
0 comments posted 20yrs posted by kenh

8 /4 white oak

I bought some 8/4 white oak (quarter sawn) (mucho dinero) expecting to get 1 3/4" thick stock. By the time I take the b...
10 comments posted 20yrs
posted by oak77539
10 comments posted 20yrs posted by oak77539

Roy Underhill is coming!

That's right! Roy will be at the Northeastern Woodworker's Association's Woodworker's Showcase this year! Teri Masaschi...
5 comments posted 20yrs
posted by nospam
5 comments posted 20yrs posted by nospam

Here's Your Cheap Shop - NC

All I know about 'em is, they're listed in one of the local bargain papers. Good way to get an inexpensive shop. Used M...
22 comments posted 20yrs
posted by Jakofalltrades
22 comments posted 20yrs posted by Jakofalltrades

Great workshop layout tool

I stumbled across this workshop layout tool from Delta. While it shows profiles for ONLY Delta and Porter-Cable tools,...
1 comments posted 20yrs
posted by mjwallace
1 comments posted 20yrs posted by mjwallace