Woodworking Forum

  1. Home
  2. Woodworking Forum
51629 Threads Posts
to

Worth reading in Woodworking Forum

WWing sights in Minneapolis-St.Paul, MN ??

I've got 7 Corners Hardware, Xylos Gallery and maybe Memory Makers Antiques if I want to head to Red Wing. Any others th...
3 comments posted 20yrs
posted by JayPique
3 comments posted 20yrs posted by JayPique

Reclaimed wood, pests and kiln drying

I am considering using reclaimed barnwood for an upcoming project, the end result of which is going to be installed in...
6 comments posted 20yrs
posted by designtaco
6 comments posted 20yrs posted by designtaco

any timber experts here?

I've purchased some acreage to build a house on, and where the house is going to be built it is mostly woods. The trees...
12 comments posted 20yrs
posted by Locutus
12 comments posted 20yrs posted by Locutus

HVLP sprayers.

I "Googled" the topic but didn't find anything like a consensus. I'm looking for an HVLP sprayer (w/turbine) in the "und...
25 comments posted 20yrs
posted by thesameoldme
25 comments posted 20yrs posted by thesameoldme

Using a Router for aJjointer

Start by confirming that the infeed table and out feed table can be adjusted where they are flat and true to each other...
6 comments posted 20yrs
posted by speedliner
6 comments posted 20yrs posted by speedliner

Grinder Size/Speed

I do not like to use a grinder as slow as 1750 rpm. it just seems to wear away at what I'm grinding rather than cutting...
1 comments posted 20yrs
posted by speedliner
1 comments posted 20yrs posted by speedliner

Can I cut my shims?

Last night I spent a couple agrravating hours trying to zero in on 15/32" with my Freud 208 stacked dado, but eventuall...
8 comments posted 20yrs
posted by dukes909isnt
8 comments posted 20yrs posted by dukes909isnt

Rouges Gallery?

During the day I produce websites. So I was thinking we could have a site with a few images of the people on here so if...
16 comments posted 20yrs
posted by ca
16 comments posted 20yrs posted by ca

Michael Fortune - design with reproduction in mind

Most of use seldom do any piece more than once, and often go at making a piece with the Marketing Department's "Ready -...
7 comments posted 20yrs
posted by charlieb
7 comments posted 20yrs posted by charlieb

Panasonic - poor customer service.

Short version: Panasonic customer service is bad, and I may be screwed out of a free 12v drill body I was supposed to r...
12 comments posted 20yrs
posted by JayPique
12 comments posted 20yrs posted by JayPique

Rechargeable battery rebuilding

There were several discussions in this newsgroup relating to rebuilding batteries. As I remember, there were several fa...
15 comments posted 20yrs
posted by jeppley
15 comments posted 20yrs posted by jeppley

Wood identification?

Hi, I've placed a Photo Gallery at: http://www.twaynesdomain.com/GarageSale/Category/Garage/garage.htmlwhich has 4 larg...
6 comments posted 20yrs
posted by nobody
6 comments posted 20yrs posted by nobody

grinder speed, size and sharpening

I am looking at grinders to sharpen stuff including lathe chisels. Most books/resources suggest the bigger the wheel th...
8 comments posted 20yrs
posted by gpagmail-news
8 comments posted 20yrs posted by gpagmail-news

Hidden shelf runners

Im making a cabinet for a friend. It a 70" long open cabinet solid maple top and 4 uprights 11/2" width the 3 shelves i...
7 comments posted 20yrs
posted by ca
7 comments posted 20yrs posted by ca