Woodworking Forum

  1. Home
  2. Woodworking Forum
51629 Threads Posts
to

Worth reading in Woodworking Forum

nice burly ash veneer in Montreal?

Dear Woodworkers, I would like to hear from woodworkers that know where can I look for some nice veneer in Montreal? I'...
4 comments posted 20yrs
posted by dr.mutaciones
4 comments posted 20yrs posted by dr.mutaciones

Woodsmith Magazine Collection - what's it worth?

I have the entire Woodsmith collection, every issue and even duplicates. I started the collection a few years ago when...
14 comments posted 20yrs
posted by none
14 comments posted 20yrs posted by none

Making exterior latex flat

I purchased several 5 gallon buckets of exterior satin latex to paint my wood siding house, after putting some on, I no...
6 comments posted 20yrs
posted by Locutus
6 comments posted 20yrs posted by Locutus

Visit to Gettysburg, PA and Lancaster, PA areas

I am going to be visiting the Gettysburg, PA and Lancaster, PA areas soon and was wondering if there are any good woodw...
9 comments posted 20yrs
posted by chpcrvr
9 comments posted 20yrs posted by chpcrvr

Sling Chair

Does anyone have plans for a sling chair or chaise? Thanks for your time.
9 comments posted 20yrs
posted by jtnospam
9 comments posted 20yrs posted by jtnospam

Cad Learning

It is my opinion that programs like Auto Cad and some of the other top of the line products are so complete that in ord...
1 comments posted 20yrs
posted by speedliner
1 comments posted 20yrs posted by speedliner

Murphy Bed

I would like to put a Murphy bed in my room so I have been looking at Murphy bed hardware kits and from what I can tell...
4 comments posted 20yrs
posted by 1qazse4
4 comments posted 20yrs posted by 1qazse4

Mix satin and gloss poly?

I was in the local hardwood store a couple of weeks ago with the missus when I overheard a conversation between another...
5 comments posted 20yrs
posted by toddrf
5 comments posted 20yrs posted by toddrf

New Dust Collector Questions

Kicking and screaming I have been pulled into the 21st century as far as small shop dust collection is concerned. I fin...
14 comments posted 20yrs
posted by removespamlcb11211
14 comments posted 20yrs posted by removespamlcb11211

Stopper-block with Cross-cut sled?

For those that use a stopper-block on your x-cut sled for repeat cuts, do you ever have problems with the cut piece bin...
2 comments posted 20yrs
posted by JayPique
2 comments posted 20yrs posted by JayPique

Learning CAD

This post is not about which is the Best CAD, it is about learning CAD. Due to a cast on my Right foot for the next 9 w...
6 comments posted 20yrs
posted by NO Spam & NotwantSpam
6 comments posted 20yrs posted by NO Spam & NotwantSpam

Murphy, wall, hideaway bed plans

Hello Woodworkers, I am considering making a Murphy bed. I have tried to find some free plans and got a copy of the Wor...
10 comments posted 20yrs
posted by pat2REMOVE
10 comments posted 20yrs posted by pat2REMOVE

Used Lumber

I tore down a pool deck in my yard over the Spring...and now I've got tons of 2x4's and some 4x8 posts. Right now, this...
6 comments posted 20yrs
posted by PiousAudio
6 comments posted 20yrs posted by PiousAudio

Chessboard protection

Hello, I purchased a wooden chess board - it came with a small typed note. Handmade 1987. Shellac and wax 3 times. Made...
5 comments posted 20yrs
posted by JJMaaaarty
5 comments posted 20yrs posted by JJMaaaarty