Woodworking Forum

  1. Home
  2. Woodworking Forum
51629 Threads Posts
to

Worth reading in Woodworking Forum

HVLP vs. ?

I'm looking at purchasing a good spray system. I've used a HVLP 3-turbine system before and was very pleased with the r...
9 comments posted 20yrs
posted by djones
9 comments posted 20yrs posted by djones

Caftsman Table Saw Fence 24/24 any good?

Allow me to start by saying that I know there are better brands... I can attest to that by the fact that I have a very...
5 comments posted 20yrs
posted by bremen68
5 comments posted 20yrs posted by bremen68

band saw blade length question

Good Morning I had a Grizzly G0457 14" bandsaw. Grizzly says that the length for the blade is 106". I would like to cha...
6 comments posted 20yrs
posted by dave
6 comments posted 20yrs posted by dave

Shop Ideas?

x-no-archive:yes How big is the area you work. Right now I have everything in my garage and it is very cramped. And a p...
13 comments posted 20yrs
posted by stryped
13 comments posted 20yrs posted by stryped

table saw wheels

I have a table saw I want to put wheels on to move it around. Rather than having a frame setup with all 4 wheels, I wou...
7 comments posted 20yrs
posted by papadoo1
7 comments posted 20yrs posted by papadoo1

Todd

Anyone here know "Todd" personally? he posted a message about 10 days ago and then dropped out of sight. He lives in th...
3 comments posted 20yrs
posted by perfectioninwood
3 comments posted 20yrs posted by perfectioninwood

55 Gallon Drum Rotator Made of Wood

A while back I saw plans on the Internet for a 55 gallon drum rotator made of wood, but I don't recall where I saw that....
7 comments posted 20yrs
posted by bob.jones
7 comments posted 20yrs posted by bob.jones

FA: Nice Delta 10" Contractor's Table Saw, Mesa, AZ

Local pickup only, Mesa, AZ Auction starts at $1 with no reserve! No room for it, must go. http://cgi.ebay.com/ws/eBayIS...
0 comments posted 20yrs
posted by escarcegaNOSPAM
0 comments posted 20yrs posted by escarcegaNOSPAM

Picked a knob for my big ash table....

Hello everyone, Thank you everyone for your suggestions on knobs for my big ash table. My intentions were to try to tur...
2 comments posted 20yrs
posted by davefred2001
2 comments posted 20yrs posted by davefred2001

Rip question on table saw

This may seem a basic question but the answer eludes me. I want to rip a piece of crown moulding on my table saw to nar...
3 comments posted 20yrs
posted by agrazi7401
3 comments posted 20yrs posted by agrazi7401

Guitar Building

Grizzly Tools has some kits Don Dando
3 comments posted 20yrs
posted by speedliner
3 comments posted 20yrs posted by speedliner

Polyurethane problem

I'm refinishing a chest of drawers, and the last part of the job is the top. I've sanded it nice and smooth with 320-gr...
5 comments posted 20yrs
posted by bsiano
5 comments posted 20yrs posted by bsiano

strange router bits

I have discovered that I like machining aluminum and brass almost as much as I like machining wood. It is surprising ho...
6 comments posted 20yrs
posted by spamsucks
6 comments posted 20yrs posted by spamsucks

Re Fixing the yoke on a Jack Plane

The yoke (not the tote) can be broken by trying to close the gap between the yoke and blade depth adjusting screw via b...
0 comments posted 20yrs
posted by srazor
0 comments posted 20yrs posted by srazor