Woodworking Forum

  1. Home
  2. Woodworking Forum
51629 Threads Posts
to

Worth reading in Woodworking Forum

CHAIRMAKER'S DEVIL

http://www.woodcentral.com/cgi-bin/readarticle.pl?dir=shop&file=articles_736.shtml Spokeshave. JOAT I am not paranoid. I...
0 comments posted 20yrs
posted by Jakofalltrades
0 comments posted 20yrs posted by Jakofalltrades

TURNED HANDLE BREAD KNIFE

http://www.woodturningdesign.com/onlineproject/breadknife.shtml I'm not interested in making one of these, so didn't go...
0 comments posted 20yrs
posted by Jakofalltrades
0 comments posted 20yrs posted by Jakofalltrades

I need some HELP ! ! !

Guys, I am starting my first project. I am very familiar with tools for building but I'm doing my first nice piece. I h...
8 comments posted 20yrs
posted by chrislvswood
8 comments posted 20yrs posted by chrislvswood

FOLDING SLED

http://countryplans.com/vintage_farm//kids/SMOct52FoldingSled.pdf This was probably posted before, but I figure some of...
0 comments posted 20yrs
posted by Jakofalltrades
0 comments posted 20yrs posted by Jakofalltrades

REDWOOD CANOE

http://countryplans.com/vintage_farm//boats/PSMar67RedwoodCanoe16.pdfJOATI am not paranoid. I do not "think" people are...
0 comments posted 20yrs
posted by Jakofalltrades
0 comments posted 20yrs posted by Jakofalltrades

COIL ENGINE BOAT

http://www.sciencetoymaker.org/boat/flogelInstructions.htm This definitely entails the use of wood. JOAT I am not parano...
0 comments posted 20yrs
posted by Jakofalltrades
0 comments posted 20yrs posted by Jakofalltrades

Wimpy compressor, Critter my only choice?

I've read a few of the threads and it seems that my only choice for using my wimpy compressor with a spray gun, is the...
12 comments posted 20yrs
posted by me7
12 comments posted 20yrs posted by me7

Cylinder sizing?

I need some large quarter-round molding. The finished size must have have a "radius" of 3" - that is, the distance from...
28 comments posted 20yrs
posted by JayPique
28 comments posted 20yrs posted by JayPique

wood staining techniques

Can someone describe the basic pros/cons between minwax regular wood stain and then applying polyurethane...stain with...
4 comments posted 20yrs
posted by trinaz
4 comments posted 20yrs posted by trinaz

cutting straight edge on table saw ?

I have a number of rough edged 8" wide planks I need to have on straight edge on. On my table saw with a Bessemer fence...
9 comments posted 20yrs
posted by trinaz
9 comments posted 20yrs posted by trinaz

Older Delta Jointer question

I've just acquired an older jointer - model 37-255 6" Delta. It's got 3 cutter heads and 17" in feed and out feed table...
3 comments posted 20yrs
posted by lowellpickett
3 comments posted 20yrs posted by lowellpickett

Horse power, horse hockey

I know it's a commonplace around here, but I just have to vent. I would like to meet the marketing people who expect me...
15 comments posted 20yrs
posted by burright65
15 comments posted 20yrs posted by burright65

Rocking Horse for Church - a.b.p.w

Posted pictures of a rocking horse I made for a church raffle. RonB
0 comments posted 20yrs
posted by rbrogan
0 comments posted 20yrs posted by rbrogan

Walnut Crown Molding advice

I have a garage full of walnut and am going to be making some crown molding for my kitchen and family room. I have a ni...
6 comments posted 20yrs
posted by of_the_rose
6 comments posted 20yrs posted by of_the_rose