Woodworking Forum

  1. Home
  2. Woodworking Forum
51629 Threads Posts
to

Worth reading in Woodworking Forum

New Delta X5 Unisaw wont kick on!

I just installed my new 3hp unisaw by delta, and I have traced power all the way into the motor when I puch start, yet...
2 comments posted 20yrs
posted by matthewrita
2 comments posted 20yrs posted by matthewrita

Hard to believe I can't find the answer....

...to this question. Long story short: tried to remove some oil stain I slopped on the window pane using mineral spirit...
4 comments posted 20yrs
posted by petengail
4 comments posted 20yrs posted by petengail

Review: Harbor Freight Dust Collector

I've recently come to the conclusion that my shop-vac just wasn't doing a good enough job at dust collection. When a Ha...
8 comments posted 20yrs
posted by mxfTWOTWOFIVE
8 comments posted 20yrs posted by mxfTWOTWOFIVE

Old Delta Table Saw Extension

I'm thinking of making an offer on an old Delta 9" tilting arbor table saw circa late 1950's. It doesn't have any table...
2 comments posted 20yrs
posted by Novice
2 comments posted 20yrs posted by Novice

CHISEL HOLDER - For Wood Lathe

http://www.shopsmith.com/ownersite/proj_articles/chiselholder/index.htm This is geared to a Shopsmith, but easily enoug...
5 comments posted 20yrs
posted by Jakofalltrades
5 comments posted 20yrs posted by Jakofalltrades

Air Cleaner

I'm looking to get an air scrubber for my shop. I've read articles on several and am leaning toward the JDS 14022 750-E...
8 comments posted 20yrs
posted by usenetonly
8 comments posted 20yrs posted by usenetonly

CUTTING FINGER LAP JOINTS WITH THE TABLE SAW

http://www.shopsmith.com/ownersite/proj_articles/lapjoints/index.htmJOATIt's not hard, if you get your mind right. - Gra...
0 comments posted 20yrs
posted by Jakofalltrades
0 comments posted 20yrs posted by Jakofalltrades

Cleaning the router bit from glue...

Hi all, I'm flush trimming a particleboard panel covered with a 2mm mahogany plywood. The plywood is glued to the parti...
4 comments posted 20yrs
posted by sammybar
4 comments posted 20yrs posted by sammybar

octagon rafter table

Can anyone point me to an online resource listing the octagon rafter table values that would have appeared on older fram...
5 comments posted 20yrs
posted by ue191
5 comments posted 20yrs posted by ue191

Chair plans available?

My wife wants 4 new dining room chairs. I don't normally use plans, but have never made a chair before, so I think it m...
10 comments posted 20yrs
posted by Toller
10 comments posted 20yrs posted by Toller

More good stuff on Junk Brothers

This week featured the brothers crosscutting an approx 8' x 1' board ... of course they used the fence, with about 1 1/...
3 comments posted 20yrs
posted by locutus_atai
3 comments posted 20yrs posted by locutus_atai

1/4 drive in hitachi m12v?

I've never used a router, bought a M12V. I see that router bits aint cheap and I'd like to get a cheap set just to try...
33 comments posted 20yrs
posted by castle
33 comments posted 20yrs posted by castle

Polyeurethane for interior of an exterior door

I have just finished sanding and staining the interior of an exterior door. Should I use interior or exterior polyeuret...
9 comments posted 20yrs
posted by scott21230
9 comments posted 20yrs posted by scott21230