Woodworking Forum

  1. Home
  2. Woodworking Forum
51629 Threads Posts
to

Worth reading in Woodworking Forum

painting hardboard

Using 1/8" dark brown hardboard as drawer bottom for very small drawers with little load..color is too dark(brown)..can...
7 comments posted 19yrs
posted by carruths
7 comments posted 19yrs posted by carruths

Cord for Cordless DeWalt tools

I have a set of 18-volt cordless DeWalt power tools that I got about 3 years ago. Since I use them rather infrequently,...
35 comments posted 19yrs
posted by heyyou
35 comments posted 19yrs posted by heyyou

California walnut by mail

I'm warming up to buy 100-200 b.f. of Cal walnut. Anyone had experience with "This Old Woodpile", or "Goby Walnut Produ...
9 comments posted 19yrs
posted by cgcurlybracketsbraggjr
9 comments posted 19yrs posted by cgcurlybracketsbraggjr

Miter saw accuracy, how much do you need?

i just bought a cheap 10" denali miter saw on amazon -- $47 delivered! -- and, having never used a miter saw before, i'...
12 comments posted 19yrs
posted by floatee
12 comments posted 19yrs posted by floatee

Fondled a Festool Domino

Yesterday, while visiting Coastal Tool, I got to paw over a Festool Domino for quite a while. NICE tool! It has a very...
43 comments posted 19yrs
posted by beech23pilot
43 comments posted 19yrs posted by beech23pilot

Sanding Edges with drum sander?

I have a 25" drum sander and I've just started a job that is going to leave me with a lot of edges to sand. Call me pic...
16 comments posted 19yrs
posted by NoSpam
16 comments posted 19yrs posted by NoSpam

Stickley - Greener Than Greene & Greene

Being one who is unable to pass up free wood, I finally got around to cutting up maybe 25 raised panel cabinet doors to...
1 comments posted 19yrs
posted by charlieb
1 comments posted 19yrs posted by charlieb

In search of a measurement conversion table/chart

In times past there was a small chart/table with lots of conversions from decimal to Imperial/Metric/... above the benc...
14 comments posted 19yrs
posted by nospambob
14 comments posted 19yrs posted by nospambob

Cabinet Doors

In planning for our kitchen remodel, my wife and i have decided to replace our kitchen cabinet doors and refinish the e...
16 comments posted 19yrs
posted by indulf
16 comments posted 19yrs posted by indulf

Vise recommendation needed

I am ready to build my first workbench. I bought a Taunton book and will probably be making a 'traditional' style bench...
16 comments posted 19yrs
posted by NunyaBiznas
16 comments posted 19yrs posted by NunyaBiznas

Silestone as Router Table Top?

I believe I saw a post here where someone was gloating about having found silestone at a good price to make a router ta...
8 comments posted 19yrs
posted by JoeBleau
8 comments posted 19yrs posted by JoeBleau

I want a Woodcraft (in NJ)

Had some time available and the need for a cabinet scraper so decided to take a run from the office in Trenton to Woodc...
13 comments posted 19yrs
posted by NunyaBiznas
13 comments posted 19yrs posted by NunyaBiznas

Basement stairs

Stairs have wafer board applied and I want to install pine stair threads = but not sure what to use for the landing.Need...
1 comments posted 19yrs
posted by joe837
1 comments posted 19yrs posted by joe837

stone veneer on center island

could anyone help me with how to go about putting a stone veneer on a center island in kitchen? the stone is a rust colo...
6 comments posted 19yrs
posted by HighIsland
6 comments posted 19yrs posted by HighIsland

Wood For TV Stand

Greetings, I've decided our HD Projection TV needs to be higher off the floor. The set weighs 150lbs and the base is 50...
9 comments posted 19yrs
posted by Sawdust93
9 comments posted 19yrs posted by Sawdust93