Leaking kettle spout

Our Russell Hobbs kettle which is similar to this one here:

formatting link
started to leak from the joint between the spout and the body of the kettle. As you pour, water runs down the outside of the kettle from the seam and drips everywhere.

Any suggestions on how to reseal the joint with something that will withstand the heat?

Reply to
Triffid
Loading thread data ...

formatting link
> has started to leak from the joint between the spout and the body of the

They all do this eventually. The only permanent cure I've ever seen is silver solder.

Reply to
Huge

Would a dab of silicone shower sealant not work?

Reply to
GB

I can give it a try - but whether it would withstand the heat of a boiling kettle I don't know.

JB Weld Coldweld appears to probably be the best bet - but by the time you've spent £5.25 plus postage on a *possible* repair - the simplest thing would probably be to buy a new kettle!

It's annoying, however, when it's still working perfectly apart from the leaking spout.

Reply to
Triffid

Mum's K2 did it after nearly thirty years - I did the decent thing and bought her a new one.

Reply to
Skipweasel

I seem to have achieved a result using super-glue. I just ran some SG around the seam, let it dry and gave it a try. No leak. How long it will last I don't know - but I thought it was worth a try.

Reply to
Triffid

18 months is our average for a kettle. The last one did not switch itself off and turned the kitchen into a sauna. >
Reply to
Mr Pounder

That kettle, for me, marks the begining of an anoying anti DIY trend that continues to this day. The "security screw".

Reply to
Graham.

If your super glue fails try silicone it should stand the heat as many bikers use silicon to seal the exhaust gasket and thats gotta be more than

100C.
Reply to
SS

Ours died at Christmas after about 15 years of stalwart service - and it was only a cheap one to start with. I was rather miffed that I couldn't find a suitable spare, and even more miffed that in this era of alleged "choice" I can't find a yellow kettle anywhere.

I have a neighbour who reckons her kettles last about 6 months before they're scaled up and useless. I asked her if she ever descales them and she just looked blank. I descale ours about once a week when I do the coffee maker - the not-quite-spent formic acid goes from one to the other - which is OK until you forget it's in there overnight and make a cup of coffee with it.

Reply to
Skipweasel

continues to this day. The "security screw".

The only security screw that's ever caused me much grief[1] are those triangular things that McDeadthings use on the toys that accompany their McDespair kids meals.

[1] Apart from dozens and dozens of the sort that have a ramped slot. Someone fitted several dozen skylight domes to a handbag factory in Crawley some time in the late 70s but didn't think to put the clear ones where the clear ones were supposed to be and the frosted ones likewise. So I had to go and take the damned things off and refit 'em. That was a miserable time on a cold wet roof doing fiddly jobs with numb fingers.
Reply to
Skipweasel

In message , GB writes

No, that's low modulus silicone

High modulus silicone (e.g. Hylomar, as sold in halfords as a gasketing compound) would be better

Reply to
geoff

Electric? Yellow kettle???????????????

Well, we live in the superior north, no need to descale.

Mr Pounder

Reply to
Mr Pounder

formatting link

Reply to
Mr Pounder

We had two RH st. st. kettles that did the same - no longer even consider RH. Did solder one around the outside of the seam - prolly not a really good idea, but it worked.

Reply to
PeterC

In message , Skipweasel writes

A tip for preventing kettles from scaling up....

My water is unbelievably hard (Chiltern chalk). I've found that one of those scale collectors (balls of stainless steel 'wire wool') dropped into the kettle EXTREMELY effective in preventing scale. The element is virtually untouched, and the scale collector scales up instead. For example:

They only cost about £1-80 in DIY shops.

Before the collector gets to much scale on it, you just roll it between your hands under a running tap. Almost all the scale detaches, and you're left with a shiny ball of wool again. It will last for years. The kettle will go for months and months before you feel the urge to maybe give it a quick de-scale. And, of course, you can also de-scale the collector if you have let it get too caked up.

Reply to
Ian Jackson

Yes - made by Alba.

The old one was yellow, and it went rather nicely with the kitchen decor. I thought it'd be nice to replace it with another yellow one - but couldn't find one. I didn't try /that/ hard, 'cos it really wasn't that important - but I'd have liked one if I could have found one at a reasonable price without too much effort.

Reply to
Skipweasel

Yup, they're very good, and we had one in the old kettle before it died. I put them somewhere safe....

Reply to
Skipweasel

We're fortunate in living in a soft water area (Cheshire). Our kettles never require de-scaling. We did live in Sussex for a few years and I can remember the 'fur' inside the kettles there.

Reply to
Triffid

You could have bought a new one in a similar colour, given it a rub down with some wet and dry, paid for some stove enamel yellow spray and there you are!

>
Reply to
Mr Pounder

HomeOwnersHub website is not affiliated with any of the manufacturers or service providers discussed here. All logos and trade names are the property of their respective owners.