Aqualise Aquarian E96 SHower - not getting hot, no pressure

I'm looking for a diagnosis:

Aqualisa Aquarian E96 mixer shower (hot and cold supply). Here:

formatting link
't get hot at all. Turn up to full hot =3D very slow shower, more of a dribble, only slightly = warm. Turn down to cold - pressure goes up to normal, but stone cold.

I still have very hot running water at normal pressure. I still have functioning central heating. Heating has been off for about 3 months due to the weather. Hot water comes on for an hour in the morning and an hour in the evening. Tank set to max (90 degrees). Nothing has changed in the house, plumbing wise. We don't appear to have an= y leaks. I've bled all of the radiators - no effect. This problem occurred instantly, not a gradual degradation. One morning I h= ad a lovely hot, high pressure shower, with the temperate control set to ar= ound 2 out of 15 (1 being cold, 15 being hot). The next day, with teh cotnr= ol on 15 out of 15, i.e. max hot I get a lukwarm dribble.

Aqualisa support say the cartridge is screwed. =A3142 for a new one, and pr= obably a plumber to fit it.

Thoughts? Other than "buy a new cartridge"!

Cheers! Jon

Reply to
Jon Parker
Loading thread data ...

formatting link
> Symptoms:

a lovely hot, high pressure shower, with the temperate control set to around 2 out of 15 (1 being cold, 15 being hot). The next day, with teh cotnrol on 15 out of 15, i.e. max hot I get a lukwarm dribble.

probably a plumber to fit it.

At the risk of stating the bleeding obvious, it's broken. Personally I would start by taking it apart, because you then might find something obvious, like that the control knob no longer turns the bits inside, perhaps because they have seized up with limescale.

Reply to
newshound

In message , Jon Parker writes

Try the shower doctor site.

On my Aqualisa no cold= no hot. Check the cold supply as well.

regards

Reply to
Tim Lamb

Aqualisa Aquarian E96 mixer shower (hot and cold supply). Here:

formatting link
't get hot at all. Turn up to full hot = very slow shower, more of a dribble, only slightly warm. Turn down to cold - pressure goes up to normal, but stone cold.

I still have very hot running water at normal pressure.

** So the problem is not in the hot water system or the boiler ** ********************************************************* I still have functioning central heating. Heating has been off for about 3 months due to the weather. Hot water comes on for an hour in the morning and an hour in the evening. Tank set to max (90 degrees). Nothing has changed in the house, plumbing wise. We don't appear to have any leaks. I've bled all of the radiators - no effect. ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ All the above seems like a vain attempt to find magic which will avoid paying for a shower repair. $$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$ This problem occurred instantly, not a gradual degradation. One morning I had a lovely hot, high pressure shower, with the temperate control set to around 2 out of 15 (1 being cold, 15 being hot). The next day, with teh cotnrol on 15 out of 15, i.e. max hot I get a lukwarm dribble.

Aqualisa support say the cartridge is screwed. £142 for a new one, and probably a plumber to fit it.

Thoughts? Other than "buy a new cartridge"!

*********************************** Happened with my Aqualisa shower. Cartridges don't last forever. The link you posted shows 1996-99 so the shower is up to 16 years old. You can fit a new cartridge yourself but it can be very fiddly so you have to be a confident and competent DIYer (or think you are) to have a go at this. You also have to be careful to get the right cartridge, as the shower body sometimes coms with different cartridges for high and low pressure, for example.

The manufacturer has told you exactly what is wrong and what is required to fix it. Presumably the cost has you searching for an alternative cheaper explanation. By all means check (as suggested) that something hasn't broken/come loose but I would take a deep breath and prepare to spend some money. The only cheaper alternative could be to buy a budget thermostatic shower valve which fits onto the same connectors. - you might be able to get a unit for less than the £142 for the cartridge. However it is possible that replacing the cartridge could give you another

15 years service from the shower. How much do you like the shower? If it meets all your needs a repair may be the best long term option.

Cheers

Dave R

Reply to
David WE Roberts

Yep! That's it exactly! I'm not going to lie!

Thanks for your replies group, new cartridge it is then.

Reply to
Jon Parker

Having spent ages trying to cure a dripping one by stripping it and fitting lots of new O rings etc without success, no. They seem to defy repair.

They are easy enough to fit, though, once you've turned the water off.

Reply to
Dave Plowman (News)

I replaced one a few years back and found that the new one although the approved replacement required shorter pipe feeds and I had to trim 5mm off the pipework.

Reply to
curious

The cartridge fits in the existing housing.

Reply to
Dave Plowman (News)

Well, riddle me this then folks.

Just took the cover off, disconnected the shower hose. Everything inside looked okay, the knobs still turned the cartridge insides etc.

I ran it for a few seconds with the outlet hose off and it was coming out piping hot. Put it all back together and it's still coming out piping hot and at normal pressure!

Could it have been something as simple as blockage in the outlet hose? Some sort of air-lock? I'm glad it's working but I want to understand what's happened?

Reply to
Jon Parker

looked okay, the knobs still turned the cartridge insides etc.

piping hot. Put it all back together and it's still coming out piping hot and at normal pressure!

sort of air-lock? I'm glad it's working but I want to understand what's happened?

Apparently my old GP used to write GOK in the notes to cover things like this. Glad you got the result; I reckon it is usually worth dismantling mechanical things to try to see what is going on. When there are moving parts it may just be a bit of grit or sticky residue that's stopping something moving correctly.

Reply to
newshound

HomeOwnersHub website is not affiliated with any of the manufacturers or service providers discussed here. All logos and trade names are the property of their respective owners.