Closed in my soffits before baffles went in - how bad is this?

Nov 11, 2026 Last reply: 1 week ago 4 Replies
Saved reading

First reply

LynxAnvil

I've done a few cathedral ceilings in places with crazy humidity, and honestly, skipping the venting altogether is the more robust approach if you are using closed cell foam. When the house is constantly dealing with moisture, creating an unintended air gap is just asking for…

Read the full reply

So I'm an owner builder and I think I messed up the order of operations on my cathedral ceiling. Framing's done, roof deck is on, and I went ahead and installed the soffit material before putting any vent channels or baffles in the rafter bays. Didn't even think about it until I was up there running wire last weekend and realized there's no clear air path from the soffit up toward the ridge. House is in a humid climate with real winters, so I know ventilation matters. My gut says I can still salvage it by cutting access holes in the soffit from a ladder and sliding baffles up into each bay before I insulate, but that sounds miserable for a long roof line. The other option folks throw around is skipping ventilation entirely and doing closed cell right against the deck so it's unvented.



Anyone been in this spot? Is cutting the soffit after the fact a reasonable fix, or would you just go unvented and sleep fine? I'm curious how much I should stress about this either way.


I've done a few cathedral ceilings in places with crazy humidity, and honestly, skipping the venting altogether is the more robust approach if you are using closed cell foam. When the house is constantly dealing with moisture, creating an unintended air gap is just asking for trouble down the line with mold or rot in the wood. I saw a recent build where they left the soffits open and just went with the rigid foam batts directly against the plywood deck and then taped the edges. It felt much cleaner and simpler. Going around cutting the soffit later sounds like a massive pain, especally when you're dealing with a long run of flashing and gutters. You're essentially trying to fix a planning error with construction work that shold have been done right the first time. If you are allready planning to go with closed cell foam, which is what I'd steer you toward for that climate, then the idea of drawing fresh air into the rafter bays is largely moot anyway.

My expirience suggests that sealing the thermal barrier tight is the safest bet here. The structural integrity of the roof assembly is more important than providing a specific air path for minimal ventilation, especially if that air path is going to just help pull moisture in during a heavy snow event. Trust your gut on the unvented route and seal up those penetrations and you should be fine.

I went through this exact headache on a project last summer. The guy had installed his sheathing and then decided to hang his fascia board right against the roof deck before even installing the bormaster baffles. Like the situation you described, he worried about that clear air path. My gut told me that while the closed cell idea sounds simple, sealing it up completley under those humid conditions is a big risk for the wood itself.

If you are going to go with the soffit modification, don't just cut holes. That's amateur hour. You need to frame a proper collar around the soffit opening, seal the edges with high-grade foam, and then install a continuous ventilation tee up there at the ridge. The goal isn't just air flow, it's balanced pressure. You want intake at the low point and exhaust at the high point. I found that even with a complex roof line, taking an hour to properly frame and seal those access points is much better than trusting a completely airtight envelope. If the insulation itself is high quality, you can manage the moisture internally, but the attic needs that breathing room to prevent condensation from forming right under the deck sheathing.

Following this becasue my garage ceiling has the same situation, no air path at all, and I just sprayed foam right against the boards and called it a day. Three winters in, no drips, no smells, nothing wierd. That said, the foam bill hurt way more than regular fluffy stuff would have. Is the foam really the only way to do an unvented ceiling, or can you build up those stiff board panels with sealed edges and get the same result for less money?

Agree with the guy who did the fascia fix last summer, cutting in after the fact is not as bad as it sounds. I had to do almost the same thing on my cabin when I boxed in my soffits before the baffles went in. I cut a slot in the soffit over each rafter bay with a jig saw, slid the baffle up until it hit the deck, and screwed a strip of vented soffit back over the slot. Whole roof took me two weekends and a lot of ladder time, but the air path is there now and I sleep fine about it. Cheaper than the foam route too, if your bays are deep enough to hit your r value with fluffy insulation plus a baffle.

Join the Discussion

Have something to add? Share your thoughts — no account required.

Didn't find your answer?

Ask the community — no account required