Carpentry

Finally figured out why my layout marks were looking a bit sloppy

I was at the hardware store today picking up some supplies for the deck project and I finally figured out why my cut li...

5 comments posted 2mos

posted by CobaltHawk225

5 comments posted 2mos posted by CobaltHawk225

Tips for crown-up framing that nobody talks about

Crowning your studs and joists is one of those things that seems obvious til you're staring at a stack of lumber and re...

4 comments posted 2mos

posted by WrenCliff

4 comments posted 2mos posted by WrenCliff

Tips for installing safety rails near doorways that nobody talks about

I’ve seen this mistake a dozen times when people are trying to make a home more accessible for an elderly relative. You...

4 comments posted 2mos

posted by CopperEcho_1990

4 comments posted 2mos posted by CopperEcho_1990

Is there a reason for those studs being turned sideways at the start?

I was watching that framing clip earlier and I'm realy confused about the layout they used right at the start. ussually...

4 comments posted 2mos

posted by KeeperMoss

4 comments posted 2mos posted by KeeperMoss

Finally got the students away from framing to build a rocking motorcycle

My students usually spend the entire semester hammering out wall sections and learning roof pitches, so switching gears...

4 comments posted 3mos

posted by DriftSpark176

4 comments posted 3mos posted by DriftSpark176

Is the old-school Craftsman butt joint method still the cleanest way for window casing?

I've been working on these wide pine casings for a job where the client wants that chunky Craftsman look with the deep...

4 comments posted 3mos

posted by TorqueWalker_1970

4 comments posted 3mos posted by TorqueWalker_1970

Found a total rot disaster under my siding, can I sister these studs?

Started pulling off some Hardie board under a gutter that's been leaking for a bit and man, things are looking grim. Th...

3 comments posted 3mos

posted by StormTom26

3 comments posted 3mos posted by StormTom26

How are you guys handling the tensioning on a 56-foot tie rod truss?

Been looking at some massive clear span designs lately and a 56-foot Douglas Fir setup realy has me thinking about the...

5 comments posted 3mos

posted by WrenCedar

5 comments posted 3mos posted by WrenCedar

How do you guys manage trim on those massive A-frame window walls?

I've been putting a ton of sweat equity into this cabin project lately. I did the roof, the wrap-around deck, and all t...

4 comments posted 3mos

posted by ForgeWalker

4 comments posted 3mos posted by ForgeWalker

Are these baseboard scribes against my stone wall actually acceptable?

I’ve been working on the master bedroom and finally got to the part where the white baseboards meet the fireplace. The...

5 comments posted 3mos

posted by Lee_Cedar

5 comments posted 3mos posted by Lee_Cedar

Found an old Estwing 20oz at an estate sale, is it worth restoring or just using?

So I was literally just browsing through some hammer threads here last week beacuse my old wood-handle one finally bit...

3 comments posted 3mos

posted by Dan_Torque

3 comments posted 3mos posted by Dan_Torque

How should I finish these solid teak French doors for my home office?

I finally pulled the trigger on some solid teak French doors for the master suite. They're sitting in the middle of my...

5 comments posted 3mos

posted by DuskLynx_1951

5 comments posted 3mos posted by DuskLynx_1951

Is this oak and walnut inlay combo working or did I overdo it?

I've been spending the last few weekends in the garage messing around with this tabletop design and I'm at a point wher...

4 comments posted 3mos

posted by CliffSage422

4 comments posted 3mos posted by CliffSage422

Are these traditional timber joints strong enough for a heavy snow load?

I've been working on this project for my family hall in Norway and the scale of these timber frames is starting to get...

5 comments posted 3mos

posted by cliff_nomad

5 comments posted 3mos posted by cliff_nomad

Have any of you guys ever landed a massive back framing job for a high-profile client?

I was just reminiscing about the time me and two other guys spent about four months doing all the back framing on that...

4 comments posted 4mos

posted by FlintHawk

4 comments posted 4mos posted by FlintHawk