Carpentry

Finally got the main stringer set for the new stairs — a few observations

We finally got the central black steel stringer locked in and the first batch of thick wood treads bolted down. It was...

5 comments posted 2mos

posted by Max_Slate70

5 comments posted 2mos posted by Max_Slate70

Is it better to use one nail or two when installing hemlock bevel siding?

Work got cut short today after a massive argument between our foreman and the new guy acutally turned into a physical f...

3 comments posted 2mos

posted by RunnerCedar_1970

3 comments posted 2mos posted by RunnerCedar_1970

Just finished the interior trim on a high-end entryway — a few observations

I just wrapped up a massive trim project on a new build, and it relly tested my patience with paneling and staircase in...

5 comments posted 2mos

posted by CopperLee97

5 comments posted 2mos posted by CopperLee97

Prefabbing bullseye dormers vs. framing on the roof?

We've been looking at the architect's plans for these circular bullseye dormers and they're pretty intimidating. To kee...

6 comments posted 2mos

posted by RavenHawk109

6 comments posted 2mos posted by RavenHawk109

Update on the garage truss reinforcement — got it level finally

Knocked out the garage truss repairs this weekend with my old man and it feels good to have that sag gone. We spent mos...

6 comments posted 2mos

posted by CopperMike_1988

6 comments posted 2mos posted by CopperMike_1988

Is it actually worth building a temporary floor for crown and coffered work?

I’m looking at these two 13x15 rooms where I have to install some pretty complex coffered ceilings. The detail alone is...

5 comments posted 2mos

posted by KeeperCopper_1990

5 comments posted 2mos posted by KeeperCopper_1990

Is it better to keep my personal life quiet as a new apprentice?

I recently started as a first-year apprentice with the UBC down south. I'm 29, so a bit older than the other guys, and...

3 comments posted 2mos

posted by Nic_Dusk

3 comments posted 2mos posted by Nic_Dusk

Anyone else prefer arched alcoves over standard square framing?

I'm just finishing up my second set of built-ins and I’ve been leaning hard into the arched alcove look lately. It feel...

5 comments posted 2mos

posted by zinc_keeper_1966

5 comments posted 2mos posted by zinc_keeper_1966

Thoughts on vertical shiplap for jib doors vs. standard trim?

I’ve been looking at diferent ways to pull off a hidden jib door lately, and I can't decide if using vertical shiplap i...

6 comments posted 2mos

posted by Tom_Cobalt_1963

6 comments posted 2mos posted by Tom_Cobalt_1963

Thoughts on heavy spray foam vs. backer rod?

I just walked into a basement job to start the finish work and every single window is buried in about four inches of ex...

4 comments posted 2mos

posted by Ash_Pike_1954

4 comments posted 2mos posted by Ash_Pike_1954

Tips for the one trim tool that nobody talks about

I’ve spent years trying every fancy gadget under the sun, but I always reach for a stainless steel pry bar more than an...

3 comments posted 2mos

posted by ForgeFinder

3 comments posted 2mos posted by ForgeFinder

Why is it a universal truth that every project requires three trips to the store?

I’m working on this simple white oak bookshelf for my office, and I swear I’ve spent more time in my truck than at the...

5 comments posted 2mos

posted by anvil_drift

5 comments posted 2mos posted by anvil_drift

Is it normal for 12-inch wide cherry planks to cup if they aren't glued down in an attic?

I'm currently in the middle of a massive attic remodel and I'm second-guessing my flooring choice. I've got these 12-in...

5 comments posted 2mos

posted by RidgeEli77

5 comments posted 2mos posted by RidgeEli77

Tips for using Jikatabi on steep pitches that nobody talks about

I spent years sliding around in Vans thinking they were the gold standard for grip, but switching to Jikatabi changed e...

5 comments posted 2mos

posted by SparkIron_1957

5 comments posted 2mos posted by SparkIron_1957

How do I get the pivot point to align on my convertible picnic table?

I've been working on one of those flip-top picnic tables that converts into two separate benches, but the pivot point i...

4 comments posted 2mos

posted by forge_wren

4 comments posted 2mos posted by forge_wren