Woodworking Forum

  1. Home
  2. Woodworking Forum
51629 Threads Posts
to

Worth reading in Woodworking Forum

Unfortunate Attempt To Remove A Dent - What Now?

Hi, I made a error and could use some opinions. A table top under construction fell over and got a tiny nick. The water...
23 comments posted 18yrs
posted by abbybrown
23 comments posted 18yrs posted by abbybrown

repairing charred cabinet door

Hello, I have a cabinet door that was slightly damaged in a fire. The door is only blackened at the bottom and bottom p...
3 comments posted 18yrs
posted by kyle
3 comments posted 18yrs posted by kyle

OT: Too funny.

http://politicalticker.blogs.cnn.com/
3 comments posted 18yrs
posted by .
3 comments posted 18yrs posted by .

Ebonizing Maple - Follow Up

First, thank you to everyone for their genuinely helpful ideas. I tried most with varying degrees of sucess. Pics and my...
0 comments posted 18yrs
posted by in
0 comments posted 18yrs posted by in

Tersa knives in Australia

Hi guys, My company will be providing Tersa blades for the Australian market in a few months time. * Knife change in se...
0 comments posted 18yrs
posted by mark.jarratt
0 comments posted 18yrs posted by mark.jarratt

Recommendations on starter set of hand planes...

I keep seeing the experienced gurus here talk about the miracles they can do with hand planes (along with the high pric...
19 comments posted 18yrs
posted by NOSPAM
19 comments posted 18yrs posted by NOSPAM

What type of TS blade to "resaw" QS White Oak?

I need to split some 4/4 x 2" QS White Oak to make some thin stiles approximately 3/8" thick (minus half a saw kerf) fo...
9 comments posted 18yrs
posted by NOSPAM
9 comments posted 18yrs posted by NOSPAM

outlet/low voltage in fireplace mantel?

Hi Folks, I'm building a home and am thinking about adding a 110v outlet and low voltage (cable, ethernet, hdmi) box to...
13 comments posted 18yrs
posted by bobrich
13 comments posted 18yrs posted by bobrich

plywood or presswood

hello, I am almost finish my cutting board project, Consisting of 200 wooden block (2 inch by 4 inch, and 2 in thick)....
24 comments posted 18yrs
posted by lerameur
24 comments posted 18yrs posted by lerameur

Bandsaw blade drifts

I suspect I need a new blade but I figured I'd post my experience for input. This morning my bandsaw blade was tracking...
24 comments posted 18yrs
posted by joesiege
24 comments posted 18yrs posted by joesiege

Need Some Ideas

Some time back I told how I used my hand power plans to round out stock in my wood lathe. Had planed a side of a couple...
8 comments posted 18yrs
posted by Jakofalltrades
8 comments posted 18yrs posted by Jakofalltrades

Cart picture at a.b.p.w.

I posted a picture of a Maple cart that I built for a customer. The Domino got lots of action on this project. I even u...
5 comments posted 18yrs
posted by removespamlcb11211
5 comments posted 18yrs posted by removespamlcb11211

Newbie router question

In an attempt to broaden by woodworking skills, I bought a PC 690LR router. . My question is specifically about this ro...
7 comments posted 18yrs
posted by j
7 comments posted 18yrs posted by j

OT: Aww jeeezzzzzzzz

Dammit, dammit, dammit, dammit. I thought he would have made a great choice as a neighbour. He refused to succumb to th...
6 comments posted 18yrs
posted by Counterfitter
6 comments posted 18yrs posted by Counterfitter

TrollFilter update

New version of TrollFilter available, by the usual means (see sig below). Comments in the Change History section describ...
4 comments posted 18yrs
posted by spambait
4 comments posted 18yrs posted by spambait