Woodworking Forum

  1. Home
  2. Woodworking Forum
51629 Threads Posts
to

Worth reading in Woodworking Forum

Home Depot and power tools

Well, the folks we love to hate have done it again. The LOML and I went to Home Depot, and I got my errands done before...
106 comments posted 18yrs
posted by walt2
106 comments posted 18yrs posted by walt2

Titebond III corrosivity to ferrous metals?

Last week the only uncluttered table top in my shop was the top of my Powermatic 66 table saw. I glued up some panels a...
8 comments posted 18yrs
posted by 2pgilbert
8 comments posted 18yrs posted by 2pgilbert

Hand plane PodCast

Just found this website tonight. If you can get through PodCast #25 without picking up your hand plane and making shavi...
2 comments posted 18yrs
posted by .
2 comments posted 18yrs posted by .

Table Saw blades

I'm using the stock blade that came with my saw, and have been cutting plywood with it. On the cuts where I'm cutting f...
14 comments posted 18yrs
posted by puckdropper(at)yahoo(dot)com
14 comments posted 18yrs posted by puckdropper(at)yahoo(dot)com

Have any 'wreckers seen one of these in person?

The new JDS-3100 CK? I'm considering a 3HP cyclone DC to replace my Jet DC-1100CK and trash can. The new JDS grabbed my...
5 comments posted 18yrs
posted by beech23pilot
5 comments posted 18yrs posted by beech23pilot

Aligning hinges on box lid, or nearly anything else...

Sorry for this, but this has always mystified me. Given a small box that I can put a lid on with either a piano hinge o...
21 comments posted 18yrs
posted by tgm2tothe10thpower
21 comments posted 18yrs posted by tgm2tothe10thpower

OT FIRST RUN WOODWORKS

Just curious, are there any first run Woodworks episodes? DIY network runs the show all weekend, but I have noticed they...
103 comments posted 18yrs
posted by capncapn2000
103 comments posted 18yrs posted by capncapn2000

I screwed up! HELP! ASAP or sooner.

I've got a good series of photos here of a shop. I want to use them in the book which is supposed to leave here Friday...
3 comments posted 18yrs
posted by charliediy
3 comments posted 18yrs posted by charliediy

O/T: It' Been One Of Those days

Today was a day to run errands. It was 98F when I left, so turned on the truck A/C. It didn't work. Made a mental note...
12 comments posted 18yrs
posted by lewhodgett
12 comments posted 18yrs posted by lewhodgett

Does anyone else choose shock this way?

I'm probably an oddball, but I'll share... Am I alone in choosing stock from my pile via the "ugly" method? First, I'll...
9 comments posted 18yrs
posted by beech23pilot
9 comments posted 18yrs posted by beech23pilot

polish wooden knife scales /handles

HI all, I'm trying to fnd the most effective wway of finishing off the wooden knife scales. I've tried rouge and then b...
5 comments posted 18yrs
posted by fordavidw
5 comments posted 18yrs posted by fordavidw

New 24x40 shop

Is it practical to place all the major dust making machines around the dust collector? Like the wagon trains of old, wh...
23 comments posted 18yrs
posted by richard.carusi
23 comments posted 18yrs posted by richard.carusi

Doorway trim opinion needed

I have widen the kitchen door way almost twice the width, non load bearing wall. After installing the trim and putting...
6 comments posted 18yrs
posted by noreaster1athotmaildotcom
6 comments posted 18yrs posted by noreaster1athotmaildotcom

Dyes and glue-up

I've been experimenting with dyes recently, something I've never tried before. I'm about to get started on a first proj...
4 comments posted 18yrs
posted by fakeaddress
4 comments posted 18yrs posted by fakeaddress