Woodworking Forum

  1. Home
  2. Woodworking Forum
51625 Threads Posts
to

Worth reading in Woodworking Forum

Extra long up-spiral router bits

Have searched and cannot find a 1/2 in. up-cut spiral router bit longer than 2 in. cutting depth. Does any body know if...
17 comments posted 17yrs
posted by victorj
17 comments posted 17yrs posted by victorj

cleaning carbide tools

I have a 1/4" carbide sanding drum and an orb for my dremel tool. It has gunked up and for the life of me I can't get i...
9 comments posted 17yrs
posted by noone
9 comments posted 17yrs posted by noone

Wooden Economy

I spent last Wednesday through Friday in New Orleans at the Forest products Machinery and Equipment Exposition. The sho...
2 comments posted 17yrs
posted by basilisk
2 comments posted 17yrs posted by basilisk

Removing an Antique Label

I am restoring an old mantle clock. Is there a way I can remove the instruction label without destroying it?
4 comments posted 17yrs
posted by dont
4 comments posted 17yrs posted by dont

Digital Angle Gauge

I picked up one of the digital angle gauges from Lee Valley last Thursday. It comes with rare earth magnets both sides...
45 comments posted 17yrs
posted by upscale
45 comments posted 17yrs posted by upscale

SCORE! Jet Parallel Clamp Cabinet Door Set

http://www.rockler.com/product.cfm?page=11417(I didn't get them from Rockler, just using the site as a reference.) Got...
12 comments posted 17yrs
posted by mike
12 comments posted 17yrs posted by mike

What is it? item 1635 (picture hanger)

Rob H., I found this image on the web: http://robinsonsantiques.com/picture-nails-hooks/picture-hooks-1-4.htm#hooks1Sen...
0 comments posted 17yrs
posted by kamontgo
0 comments posted 17yrs posted by kamontgo

Ridgid 2 1/2" finish nailer advise

I need a finish nailer to rebuild my porch railing and also will be used later for trim work around house, base board,...
11 comments posted 17yrs
posted by lamp.lighter
11 comments posted 17yrs posted by lamp.lighter

crowning bandsaw tires

Anyone have experience crowning new tires on a 36" bandsaw? Any suggestions on how to approach this task on such a large...
11 comments posted 17yrs
posted by grossboj.nospam
11 comments posted 17yrs posted by grossboj.nospam

re-finishing an old walnut table

A friend has an OLD walnut table that had a very badly damaged lacquer finish. The only way to fix it was to strip it d...
3 comments posted 17yrs
posted by l-lopez
3 comments posted 17yrs posted by l-lopez

Which compressor to buy.

Looking for feed back. I'm replaceing my old worn out 2HP CH compressor. I want one of the 60 gallon 3+HP upright model...
6 comments posted 17yrs
posted by Nirodacyar
6 comments posted 17yrs posted by Nirodacyar

RE: Screen door advice

Thanks all for the input. I will post the results when completed. The corrugated fasteners are intruding. A few of the...
1 comments posted 17yrs
posted by homefix
1 comments posted 17yrs posted by homefix

How to make a Spiral Groove in Column

I need to make a spiral groove in a couple of columns. I only have to do it in two columns and I may not do another for...
13 comments posted 17yrs
posted by eganders
13 comments posted 17yrs posted by eganders

Milwaukee 0234-6 Magnum 5.5 Amp 1/2-Inch Dril

I'm about to move into my first house--my wife and I already picked out the washer and dryer so I"m starting to shop fo...
39 comments posted 17yrs
posted by Bill_NOSPAM
39 comments posted 17yrs posted by Bill_NOSPAM

Blown the finish...not sure what to do next

Hey Guys, I'm up the creek without the proverbial paddle. I built a dinning table with bubinga top. I don't have much e...
9 comments posted 17yrs
posted by DIYMark
9 comments posted 17yrs posted by DIYMark