Woodworking Forum

  1. Home
  2. Woodworking Forum
51625 Threads Posts
to

Worth reading in Woodworking Forum

Newbie question

I need to make some wedges that will be out of nominal by four stock, that is, probably cut out of four by four. They w...
8 comments posted 15yrs
posted by pittmanpirate
8 comments posted 15yrs posted by pittmanpirate

Mortice Chisels

A week or two ago there was a thread here with someone asking about mortise chisels. The Narex brand was discussed. I n...
1 comments posted 15yrs
posted by NOSPAMrp77469
1 comments posted 15yrs posted by NOSPAMrp77469

3 phase table saw in a single phase shop

Just purchased a 3 phase 5hp Jet JTAS 10XL table saw and now am working on getting it working in my single phase shop....
8 comments posted 15yrs
posted by blbach
8 comments posted 15yrs posted by blbach

Whatcha all think of this Jointer?

I'm looking at this Grizzly jointer, has anybody seen, used, or bought one? http://www.grizzly.com/products/6-x-46-Join...
20 comments posted 15yrs
posted by jtpryan
20 comments posted 15yrs posted by jtpryan

Choosing table saw

I am looking for a mid range table saw. I am 70 so this will be the last one that I buy. I don't want to go through the...
27 comments posted 15yrs
posted by Ray
27 comments posted 15yrs posted by Ray

How to fix a gouge in a table top?

Well, actually a series of gouges. The top of my wife's mother's buffet cabinet was gouged during a move many years ago...
15 comments posted 15yrs
posted by busbus
15 comments posted 15yrs posted by busbus

Amount of lighting

Concerned that I was getting lazy, I went out and measured my ceiling joists and other structure carefully and spent my...
93 comments posted 15yrs
posted by Bill
93 comments posted 15yrs posted by Bill

Chisel Plane (DIY)

Make a chisel plane from a chisel and scrap wood. It can be used as either a rabbeting plane or a shoulder plane. Exper...
8 comments posted 15yrs
posted by bgrella
8 comments posted 15yrs posted by bgrella

O/T: Nookie Green

Speaking of colors. Enjoy Lew ---------------------------------------- An Irish man went to confession in St. Patrick C...
4 comments posted 15yrs
posted by sails.man1
4 comments posted 15yrs posted by sails.man1

Some serious wood projects

Someone has a lot of time and patience. Very cool stuff. http://completeall.com/Art-and-Design/Creativity-From-Wood-and-...
1 comments posted 15yrs
posted by Me
1 comments posted 15yrs posted by Me

Trying to square a 4x4 piece of hard maple

I am making a kitchen island that will have 3.5" square legs made from maple. I bought 2 pieces of 16/4 hard maple abou...
32 comments posted 15yrs
posted by jtpryan
32 comments posted 15yrs posted by jtpryan

Coping crown molding

A recent discussion included what looked like a portable bandsaw being used for coping crown molding, I remember seeing...
10 comments posted 15yrs
posted by upscale
10 comments posted 15yrs posted by upscale

Cutting down strip nails-anyone try this?

I purchased a variety pack of 18 ga. stainless brads with 1", 1 1/4", 1 1/2", and 2" lengths. When I received it I then...
4 comments posted 15yrs
posted by genetakae
4 comments posted 15yrs posted by genetakae

O/T: 2010 College Football

OHIO STATE..................37 Michigan.............................7 It's been a successful season. Lew
12 comments posted 15yrs
posted by sails.man1
12 comments posted 15yrs posted by sails.man1

Newbe drilling question

I'm assuming that if trying to drill overlapping 3/8" holes in the side of 2by4 stock, that using forstner bits will be...
33 comments posted 15yrs
posted by Bill
33 comments posted 15yrs posted by Bill