Woodworking Forum

51625 Threads Posts
to

Pretty wood

There have been several L O N G off topic posts recently so I thought I'd start one that was ON topic and still allow y...
38 comments posted 15yrs
posted by dadiOH
38 comments posted 15yrs posted by dadiOH

Planes for smoothing

My general woodworking skills: Modest at best My plane skills: None I recently "inherited" a Stanley block plane that I...
24 comments posted 15yrs
posted by gdguarino
24 comments posted 15yrs posted by gdguarino

MDF Base Molding Installation

The old time craftmens way to install wood baseboard molding was to run the first piece right to the inside corner and...
9 comments posted 15yrs
posted by mkaras
9 comments posted 15yrs posted by mkaras

Bass wood blocks from Heinecke

Rockler is out of the basswood blocks I have been getting, so I went searching for someplace to get some. I found Heine...
2 comments posted 15yrs
posted by oplholik
2 comments posted 15yrs posted by oplholik

Hammers

I need some ordinary hammers (12, 16, 20 oz). Are these tools in the "you get what you pay for" category? Perhaps you c...
30 comments posted 15yrs
posted by Bill
30 comments posted 15yrs posted by Bill

Sleeping with your framer ...

Actually, there is a great deal that is heartwarming in the way these two work in concert. Watch the gable raising vide...
18 comments posted 15yrs
posted by kac
18 comments posted 15yrs posted by kac

What can you use to sand a router cut?

I have a set of doors that are pretty weathered. It has a router pattern. Isn't there something that takes the shape of...
4 comments posted 15yrs
posted by kilowatt
4 comments posted 15yrs posted by kilowatt

OT- somewhat.

I directed Tim to this NG. He is at my house now discussing RVs. I think I can help him with the inspection part. Max
1 comments posted 15yrs
posted by thesameoldme
1 comments posted 15yrs posted by thesameoldme

OT: Help please. "Intellisync Corp" popup

Sorry for the OT post but you guys know more than most. IE ver 8. Lately, I've been hammered by the pop-up blocker tell...
62 comments posted 15yrs
posted by zzyzx__
62 comments posted 15yrs posted by zzyzx__

What A Mess and then some...

Background: Some time ago, I bought an old rent house and have been remodeling it, for a woodshop. The front center sec...
9 comments posted 15yrs
posted by cedarsonny
9 comments posted 15yrs posted by cedarsonny

School Shop Auction Palm Beach County FLorida

Thought to pass this along in case anything they have might interest anyone here. http://www.publicsurplus.com/sms/list...
0 comments posted 15yrs
posted by gooeytarballs
0 comments posted 15yrs posted by gooeytarballs

cabinet box material

Sorry if this is considered OT, but I thought people here would know. First-time poster here. I assume the google probl...
43 comments posted 15yrs
posted by dentaltwinmung
43 comments posted 15yrs posted by dentaltwinmung

OT: TV Tower.

I know this is OT, but I respect the opinion of many here so here it goes. I just bought a used 40' TV tower. $75 bucks...
39 comments posted 15yrs
posted by counterfitter
39 comments posted 15yrs posted by counterfitter

Miter gauge WTB

My Delta miter gauge works fine on a t-track, but the track on my Rocker router table is a stardard 3/4 without accommo...
4 comments posted 15yrs
posted by good
4 comments posted 15yrs posted by good

Sliding dovetail, part II

I finished the little stepstool I wrote about a few days ago and had an interesting experience while cutting the pins o...
8 comments posted 15yrs
posted by good
8 comments posted 15yrs posted by good