Woodworking Forum

51625 Threads Posts
to

How about a wooden bathtub?

Pic http://hackedirl.files.wordpress.com/2011/10/epic-win-photos-wood-bath-win.jpg
0 comments posted 14yrs
posted by heybub
0 comments posted 14yrs posted by heybub

Need help with Jet planer/molder

I purchased a 13 inch Jet planer/molder. After initial setup I was able to easily thickness plane lumber. The results w...
2 comments posted 14yrs
posted by l-lopez
2 comments posted 14yrs posted by l-lopez

Turning tool question

Last time I tried to use a lathe was over 40 years ago. Decided to get back into it so I bought a little mini lathe fro...
7 comments posted 14yrs
posted by vgbaron
7 comments posted 14yrs posted by vgbaron

re: dominotrick

It's called a reuleuax triangle. Look it up it's actually really cool. It a triangle that is offset on a shaft.
1 comments posted 14yrs
posted by brandonhon
1 comments posted 14yrs posted by brandonhon

Dominotricks

http://www.wimp.com/squareholes/
9 comments posted 14yrs
posted by counterfitter
9 comments posted 14yrs posted by counterfitter

Lining clamp pads - what to use?

I just bought a couple (more) Jorgensen bar clamps, the type that have soft orange pads on the jaws. But I have just st...
33 comments posted 14yrs
posted by gdguarino
33 comments posted 14yrs posted by gdguarino

OT: Basement Ceiling Insulation

We have a one-story house with a full basement. The main floor is built on 2x10 floor joists withthree-quarter plywood...
17 comments posted 14yrs
posted by gooeytarballs
17 comments posted 14yrs posted by gooeytarballs

Basswood differences

Hopefully on abpw, a pic of some basswood will show up. Just wondering what the differences are. Thanks, Paul
2 comments posted 14yrs
posted by oplholik
2 comments posted 14yrs posted by oplholik

Burnt shellac

As glue, cure time?
8 comments posted 14yrs
posted by fatherhaskell
8 comments posted 14yrs posted by fatherhaskell

Removing laminate/formica

I have a small dining room table (4 people) with an imitation dark oak laminate sheet as it's top. It's a split table w...
8 comments posted 14yrs
posted by MB
8 comments posted 14yrs posted by MB

how to fill shallow holes in workbench top

I put in a bench vise today and, as per advice from this group, used bolts, nuts and washers. I drilled a couple of fla...
7 comments posted 14yrs
posted by gdguarino
7 comments posted 14yrs posted by gdguarino

Fine WW and David Letterman!!!

If you like David Letterman, this is a must see: http://tinyurl.com/4ykkot5(LarryJ, that's my *first* tinyurl) Skip dow...
3 comments posted 14yrs
posted by Bill
3 comments posted 14yrs posted by Bill

Finally got it done

Well, I asked a lot of questions here, and got a lot of help, for that I th= ank all. Took me a loooooong time to get i...
24 comments posted 14yrs
posted by jtpryan
24 comments posted 14yrs posted by jtpryan

What Glue For Veneer?

I've repaired small veneer chips/missing pieces, using Titebond II, successfully. I now have a old dresser project with...
31 comments posted 14yrs
posted by cedarsonny
31 comments posted 14yrs posted by cedarsonny

Ridgid quiet vacuums

I'm thinking about replacing a failing Fein Turbo II with one of Ridgid's quieter vacuums. Model WD1450 is the one I lo...
15 comments posted 14yrs
posted by puckdropper(at)yahoo(dot)com
15 comments posted 14yrs posted by puckdropper(at)yahoo(dot)com