Woodworking Forum

  1. Home
  2. Woodworking Forum
51625 Threads Posts
to

Worth reading in Woodworking Forum

Drilling High Speed Steel

Trying to widen a hole on a planer blade that goes over a alignment pin on the cutterhead (DW735). I tried using a coba...
12 comments posted 14yrs
posted by brian
12 comments posted 14yrs posted by brian

The three contractors O/T

Three contractors are bidding to fix a broken fence at an Ottawa government owned house: One is from Vancouver , anothe...
1 comments posted 14yrs
posted by Spambin
1 comments posted 14yrs posted by Spambin

Cutting dados for thin shelves

Making an open front (no doors) sheet-music cabinet. This is to replace a = similar (garage sale) one that has failed....
4 comments posted 14yrs
posted by ivanvegvary
4 comments posted 14yrs posted by ivanvegvary

FS: DeWalt DC628K Cordless Nailer for Sale

DeWalt DC628K Cordless Nailer for Sale 15g DC628K 18-Volt Sequential or bump mode operation Easy access to the nosepiec...
0 comments posted 14yrs
posted by upscale
0 comments posted 14yrs posted by upscale

I think I had a clever idea

I finally found the time to cut down the two plywood cabinet boxes I mentio= ned a few weeks ago. I cut one of the "sid...
3 comments posted 14yrs
posted by gdguarino
3 comments posted 14yrs posted by gdguarino

FS - DeWalt D55141 Trim Compressor (Toronto)

DeWalt D55141 Trim Compressor 2 Gallon, 150 PSI Maximum 2.0 SCFM delivered @ 90 PSI pump, 2.0 gallon tank 79* dBA allow...
0 comments posted 14yrs
posted by upscale
0 comments posted 14yrs posted by upscale

For Sale Stuff Here?

I've got a DeWalt D55141 Trim Compressor that I'm selling. I'm wondering if posting the ad here will cause a problem?
1 comments posted 14yrs
posted by upscale
1 comments posted 14yrs posted by upscale

Rubber belting, where to buy (USA), etc

Search results produce search results within search results. Where to buy round rubber belting online? So far, I have o...
12 comments posted 14yrs
posted by jdoe
12 comments posted 14yrs posted by jdoe

Planer question

Got a Ridgid 13" planer last year, haven't used it much but, dang, it sure is noisy. Today I was planing some 1x10x30 p...
26 comments posted 14yrs
posted by ralphcompton
26 comments posted 14yrs posted by ralphcompton

Festool routers and vacs - dust collection...good?

I'm about at my breaking point with routers and dust all over the place and I'm SERIOUSLY thinking about getting the bi...
1 comments posted 14yrs
posted by mwskaneateles
1 comments posted 14yrs posted by mwskaneateles

Roadkill question

Hypothetically, if you hit a deer while driving, would you be tempted to take it home and butcher it? Mike
38 comments posted 14yrs
posted by michaeldwilson2
38 comments posted 14yrs posted by michaeldwilson2

Interesting video about shellac

http://www.youtube.com/watch?v=lQcQ0yuekZ0it's a wonder the stuff isn't $500 a pound...
9 comments posted 14yrs
posted by ichasetrains
9 comments posted 14yrs posted by ichasetrains

Ping - Bill in Indiana

Bill, sometime ago you were looking for a table saw. Did you possibly have an interest in a jointer, also? Here's one n...
12 comments posted 14yrs
posted by cedarsonny
12 comments posted 14yrs posted by cedarsonny

Round rubber pieces or pipe with ID of 22 mm?

Rubber, or any material similar to rubber. It will be pushed onto a standard 608 bearing, like a tire onto a wheel. Thi...
8 comments posted 14yrs
posted by jdoe
8 comments posted 14yrs posted by jdoe

Need advice on built-ins

I wish to build a series of built-ins along a 14 foot wall. I have to incorporate 2 desks. I've built carcasses and dra...
21 comments posted 14yrs
posted by abc
21 comments posted 14yrs posted by abc