Woodworking Forum

51629 Threads Posts
to

Okay to use Ridgid knives in a Delta jointer?

I have a Delta JT360. In HD today I saw a set of Ridgid knives for $12. Since the Delta knives are $45 (I have a set on...
7 comments posted 22yrs
posted by toller
7 comments posted 22yrs posted by toller

Re: On lateral adjustment, Bailey planes

Garret Hack said you can feel smaller tolerances than you can see. :-) I pretty much agree with him. If you can't feel...
10 comments posted 22yrs
posted by lholm
10 comments posted 22yrs posted by lholm

OT: Roofing question 6 tab shingles

I realize this is pretty off topic but have always been impressed the with wide variety of knowledge possessed by the i...
3 comments posted 22yrs
posted by jmweber987
3 comments posted 22yrs posted by jmweber987

re: sHARPENED

What is with people using the word "sharpened" in this manner (from the Vintage Saws web page) "more likely is the fact...
67 comments posted 22yrs
posted by srazor
67 comments posted 22yrs posted by srazor

New table top and music box

Howdy all, Been away from the 'Wreck for a few months - busy with other stuff and lost my motivation to work in the sho...
0 comments posted 22yrs
posted by cpowers38
0 comments posted 22yrs posted by cpowers38

Making a Log Box

I was wondering how I could go about making a box from a solid piece of wood without cutting all the way through. I may...
2 comments posted 22yrs
posted by bassburner
2 comments posted 22yrs posted by bassburner

Butcher Block Countertop

Hi. I am putting a hard rock maple countertop in my deli. I found what seems to be a good supplier that has good prices...
20 comments posted 22yrs
posted by dwhite110
20 comments posted 22yrs posted by dwhite110

Woodhaven Bandsaw Fence

http://www.woodhaven.com/SearchResult.aspx?CategoryID=153Looks pretty good. Anybody have any experience with it? How doe...
4 comments posted 22yrs
posted by emptyshell
4 comments posted 22yrs posted by emptyshell

Chair leg repair

I have a chair that the wooden leg broke in the middle. clean break in half. It is a horizontal break, not hight way. W...
3 comments posted 22yrs
posted by jneville23
3 comments posted 22yrs posted by jneville23

Planer Advice

Thanks for helping me if anyone can do so. Looking at thickness planers, 12" or so. Will not be doing a lot of 'heavy'...
13 comments posted 22yrs
posted by yo4do
13 comments posted 22yrs posted by yo4do

ROUTER Height adjustment

I am looking for a magazine article for making a height adjustment mechanism for a plunge router. I think it has been in...
3 comments posted 22yrs
posted by zwwizard
3 comments posted 22yrs posted by zwwizard

Concrete coating in kitchen

A friend did his kitchen floor in decorative grooved and stained concrete. He then put on 2 coats of a 1 part urethane...
6 comments posted 22yrs
posted by gerryforum
6 comments posted 22yrs posted by gerryforum

Record 110 block plane

Hey people, I picked up a Record No 110 block plane a while back at a flea market ($10) that I intend to use for genera...
1 comments posted 22yrs
posted by br
1 comments posted 22yrs posted by br

Melamine vs. plywood for sliding shelf bottoms

I'm in the all-important "thinking about it" stage and I'd appreciate some of the good advice I have seen posted here....
3 comments posted 22yrs
posted by mycroftt
3 comments posted 22yrs posted by mycroftt

Poplar dust

I've heard about all the exotic woods and the irritations their dust can cause but has anyone had a problem with poplar...
16 comments posted 22yrs
posted by ron.short
16 comments posted 22yrs posted by ron.short