Woodworking Forum

  1. Home
  2. Woodworking Forum
51629 Threads Posts
to

Worth reading in Woodworking Forum

How to hang a shelf on the wall

I was looking through "Design Your Own Furniture" by Jim Stack and I encountered a shelf that I thought looked nice. It...
35 comments posted 21yrs
posted by adrian
35 comments posted 21yrs posted by adrian

Drawer pull height

I built a tool cabinet that has 2 rows of four drawers. The drawers range from 4" in height to 11", my question is wher...
6 comments posted 21yrs
posted by wjpajunen
6 comments posted 21yrs posted by wjpajunen

OK, wreckers. It's 'fess up time!

And now in a burst of refreshing honesty we're all going to admit to the most useless, waste-of-money, unnecessary, whi...
348 comments posted 21yrs
posted by foggytown
348 comments posted 21yrs posted by foggytown

Edge joining and resawing for thin panels

Hello, I'm making an arts/crafts style tool chest, following a plan from Wood magazine. The back of the chest is made w...
4 comments posted 21yrs
posted by wowbagger9
4 comments posted 21yrs posted by wowbagger9

blade sharpening

Does anyone have any recommendations for a good blade sharpeing service. The only local place I've found sends their bl...
17 comments posted 21yrs
posted by dserson
17 comments posted 21yrs posted by dserson

Learning to Use a Tenon Jig

I just bought a tenon jig for my 12" General Table Saw. It seems pretty straight forward except when cutting a tenon on...
21 comments posted 21yrs
posted by glenduffNOSPAM
21 comments posted 21yrs posted by glenduffNOSPAM

Ping: Michael Baglio

Hey Mike, I'm in your neck of the woods visiting the in-laws. Any decent places for WWers besides WWers Supply near Burl...
2 comments posted 21yrs
posted by wseavey
2 comments posted 21yrs posted by wseavey

Tailed Vs Stumpy Drills

I promised the missus a (melamine) cabinet for the laundry, but to allow for shelf locations I needed to drill lots of...
24 comments posted 21yrs
posted by spamfree
24 comments posted 21yrs posted by spamfree

LV Sale

I just checked the LV site and as advertised the K body clamps are on sale. Has anyone noticed any other sale items? Che...
0 comments posted 21yrs
posted by JGS77Stamp
0 comments posted 21yrs posted by JGS77Stamp

Leveling floor for laminate install

I'm trying to level a room in preparation for the installation of laminate flooring. The laminate flooring requires the...
13 comments posted 21yrs
posted by krishna.and.craig
13 comments posted 21yrs posted by krishna.and.craig

OT: Cherry Firewood

I was quoted cherry firewood vs. "various hardwood" firewood. The cherry cost a little more, so I figured it must be "be...
10 comments posted 21yrs
posted by rileyesi
10 comments posted 21yrs posted by rileyesi

Cutting board question

Last January, we had a storm during which the top third of my Evergreen Magnolia tree landed, in various pieces, on the...
4 comments posted 21yrs
posted by glenna
4 comments posted 21yrs posted by glenna

Best way to fix stripes in baltic birch

The following illustrates the problem: http://alan.firebin.net/images/cab_stripes1.jpghttp://alan.firebin.net/images/ca...
5 comments posted 21yrs
posted by arwomack01
5 comments posted 21yrs posted by arwomack01

Makita cordless drill vs. Makita cordless drill

I am in the market for my first cordless drill, to be used around the house for decking and fencing. For about five yea...
7 comments posted 21yrs
posted by scott
7 comments posted 21yrs posted by scott

molded brass L bracket ...

I'm looking for a small (roughly 1"x1") molded (hollow in center) brass L brackets... Some of the mass produced furnitu...
2 comments posted 21yrs
posted by jason
2 comments posted 21yrs posted by jason