Woodworking Forum

  1. Home
  2. Woodworking Forum
51629 Threads Posts
to

Worth reading in Woodworking Forum

Design/construction question

I've posted a sketch of a fireplace surround in abpw. I have a question regarding the upper doors. Given that they're e...
1 comments posted 21yrs
posted by JDWHATSOBVIOUSCaff
1 comments posted 21yrs posted by JDWHATSOBVIOUSCaff

Beginner Dado question

I am new to this hobby and wanted to get some advice. a.. I am building a workbench that calls for t-track in an 80" pi...
18 comments posted 21yrs
posted by swillet
18 comments posted 21yrs posted by swillet

Re: Stop Arthritis

> Help stop Arthritis by supporting The Arthritis Foundation: > http://www.arthrirg>Reported to snipped-for-privacy@lyco...
20 comments posted 21yrs
posted by esp
20 comments posted 21yrs posted by esp

Hinges - Silver - Where to find?

Does anyone know who can supply Silver Hinges suitable for small jewelry boxes. I know about Lee Valley and many of the...
31 comments posted 21yrs
posted by notmeNO
31 comments posted 21yrs posted by notmeNO

OT: Band Saw Information

Hi, I know this may be outside the normal realm of topics, but since in know there is such a wealth of knowledge here w...
3 comments posted 21yrs
posted by cookrick
3 comments posted 21yrs posted by cookrick

UPS rant and Rockler praise

A couple weeks ago, I ordered some stuff from Rockler. They shipped the order the next day, and e-mailed me the UPS tra...
11 comments posted 21yrs
posted by collector201
11 comments posted 21yrs posted by collector201

OT - AIDS and Senior Citizens

Believe it or not, my mother sent this to me. GUESS WHO IS THE BIGGEST AIDS CARRIER!!=A0 =A0=A0=A0=A0=A0=A0=A0=A0=A0=A0...
0 comments posted 21yrs
posted by Jakofalltrades
0 comments posted 21yrs posted by Jakofalltrades

new blade change system on Bosch 1591 jig saw

I have not seen this written up in here, so I thought I would post it. There have been many threads on Bosch and Milwau...
8 comments posted 21yrs
posted by bluemax1811-newsgroups
8 comments posted 21yrs posted by bluemax1811-newsgroups

Excalibur

Thanks everybody for the help with my sliding table. I think I have it set up properly It is not all that difficult to...
1 comments posted 21yrs
posted by agi733
1 comments posted 21yrs posted by agi733

To those who have made a business out of it

What was the route that you took? Did you start by being psuedo-in business, off the books... then decide to make an of...
5 comments posted 21yrs
posted by JDWHATSOBVIOUSCaff
5 comments posted 21yrs posted by JDWHATSOBVIOUSCaff

Good method for assuring flush M&T joints.

I am in the process of building some bedroom furniture. The style is made up of mortise and tenon frames with 1/4" (rea...
5 comments posted 21yrs
posted by wyattsjunk
5 comments posted 21yrs posted by wyattsjunk

screws don't go in far enough

Recently the casing on my storm door's inside latch cracked, leaving it held by only one screw. I bought a Wright prefa...
5 comments posted 21yrs
posted by colonel
5 comments posted 21yrs posted by colonel

Yet another MDF thread

I know the general topic of MDF has been pretty much beaten into the ground (I think I've read just about every post on...
3 comments posted 21yrs
posted by dsnail
3 comments posted 21yrs posted by dsnail

Jointer and Grain Question

Yesterday in a post I saw something indicating that if you try and joint pieces larger than the width of your jointer y...
13 comments posted 21yrs
posted by megold.andrew
13 comments posted 21yrs posted by megold.andrew