Woodworking Forum

  1. Home
  2. Woodworking Forum
51629 Threads Posts
to

Worth reading in Woodworking Forum

Baseboards - dividing an angle - Fudd

Fudd asked me to depict the method I use to divide an angle and I tried to do it with limited success using text. I the...
4 comments posted 21yrs
posted by NunyaBiznas
4 comments posted 21yrs posted by NunyaBiznas

Oxygen-free finish container idea

There have been a few threads recently about usign marbles or decanting to smaller containers to keep partially used co...
18 comments posted 21yrs
posted by smeier-spamless
18 comments posted 21yrs posted by smeier-spamless

Roughing up wood - with a dado set?

I am building some bat houses, and they need rough wood so the bats can hold on to it. It is suggested to run a series...
19 comments posted 21yrs
posted by Toller
19 comments posted 21yrs posted by Toller

LINK - Steel Insert

http://www.mcfeelys.com/subcat.asp?subcat=20.15.4 Hadn't seen anything quite like this before. Wouldn't be anything I w...
4 comments posted 21yrs
posted by Jakofalltrades
4 comments posted 21yrs posted by Jakofalltrades

Re: What the heck does BORG stand for, anyway? :)

> > If you look it up in the dictionary you find.... Technology Borg A type of cyborg in Star Trek that devours everyth...
2 comments posted 21yrs
posted by removespamlcb11211
2 comments posted 21yrs posted by removespamlcb11211

Looking for ShopNotes Back Issues

Hello - For reasons beyond rational explanations I'm trying to fill out a complete set of ShopNotes issues. Through eba...
6 comments posted 21yrs
posted by kevin
6 comments posted 21yrs posted by kevin

Estimating BF in a pile of lumber

Hello, I have a lead on some low priced lumber. There is quite a bit, and I am not used to purchasing in large quantiti...
6 comments posted 21yrs
posted by bmahaney1
6 comments posted 21yrs posted by bmahaney1

Installing wave washers in TS

Anyone got any tips on getting the wave washers back into the trunion assembly that adjusts blade height on a table saw?...
3 comments posted 21yrs
posted by JayPique
3 comments posted 21yrs posted by JayPique

Lumber rack for plywood sheets etc.

I saw awhile back a plan for plywood sheets that were off of the floor and stored on a device that had 4 wheels on it....
3 comments posted 21yrs
posted by dave
3 comments posted 21yrs posted by dave

There Is a Portable

...manual typewriter that must have belonged to Jack Bobbitt that is getting in the way. Does Andrew want it? It has a...
11 comments posted 21yrs
posted by llhote
11 comments posted 21yrs posted by llhote

FS-NEW Skil XShop (New Mexico)

> For Sale: NEW Skil XShop Convertible Workshop ? 10? table saw with > digital rip fence/drill press/ router table with...
0 comments posted 21yrs
posted by BarbMoore.1ul5ln
0 comments posted 21yrs posted by BarbMoore.1ul5ln

Shoe Rack -- A simple design - Golden Ratio

Shoe Shelf or Shoe rack (Take your pick) SWMBO wanted a shelf to store shoes - so I made her one. It uses four=20 piece...
14 comments posted 21yrs
posted by will
14 comments posted 21yrs posted by will

Need Beading Shaper Cutter

Hello, I have an application where I need to make a 1/4" diameter bead on the face (show) edge of a 2 1/4" x 3/4" door...
6 comments posted 21yrs
posted by azwood
6 comments posted 21yrs posted by azwood

What to do when lint free cloth isn't lint free?

Ok.. I am nearing completion of my first project. Yeah! I put off finishing the project for a long time for fear I woul...
5 comments posted 21yrs
posted by noemail
5 comments posted 21yrs posted by noemail

General Table Saw (Canadian) Quality - and Slider

Until a few weeks ago, I was aimed at getting either a Felder or Knapp Table Saw. It would take me 18 months of saving...
9 comments posted 21yrs
posted by extiger
9 comments posted 21yrs posted by extiger