Woodworking Forum

  1. Home
  2. Woodworking Forum
51629 Threads Posts
to

Worth reading in Woodworking Forum

Designing deep kitchen pantry

I am building kitchen cabinets and part of the design is to build a tall deep kitchen pantry. It is 8' high from floor...
17 comments posted 21yrs
posted by agalkin
17 comments posted 21yrs posted by agalkin

Advice on Kufo - Sliding Table Saw

Does anyone have experience with this Taiwanese beast? Quality control looks pretty good. I want a Format (Euro) saw wi...
0 comments posted 21yrs
posted by extiger
0 comments posted 21yrs posted by extiger

Racedeck or Similar Garage Tiles?

Hi, Anybody have RaceDeck or the garage tiles from Costco in their shop? Just concerned about how well the table saw and...
2 comments posted 21yrs
posted by anybody
2 comments posted 21yrs posted by anybody

dual bevel compound miter saw vs single bevel

I just bought a dewalt 12" single bevel compound miter saw, my craftsman was just not staying accurate. I'm starting to...
10 comments posted 21yrs
posted by dserson
10 comments posted 21yrs posted by dserson

Adjustments on an old Sears RAS, and table?

I picked up an old Sear RAS at an estate auction. I know it is old because it came with 4 steel blades. It is the same...
6 comments posted 21yrs
posted by Toller
6 comments posted 21yrs posted by Toller

Need Shopnotes #55

I'm looking for a copy of Shopnotes #55. Specifically, I need the article in this issue that described building a rolli...
0 comments posted 21yrs
posted by weswitt
0 comments posted 21yrs posted by weswitt

Cast iron table saw tops

These damn cast iron table saw tops are nuthin' but trubble!!! Isn't it time to find a better solution? How about ........
18 comments posted 21yrs
posted by tomwoodman42
18 comments posted 21yrs posted by tomwoodman42

Minwax Rub on Poly........

Hello again......I had previously asked about how to finish a table that wasn't sealed......had stain, but no seal........
6 comments posted 21yrs
posted by auctionstuff
6 comments posted 21yrs posted by auctionstuff

Brazing/welding router bits: experience?

I need to modify a 1/2" router bit. The profile doesn't have to be altered. I simply want to take a standard ogee bit a...
10 comments posted 21yrs
posted by wseavey
10 comments posted 21yrs posted by wseavey

Smoothing, trueing countertop edge?

I'm working on a countertop to replace the original that was water damaged. The countertop is sort of "D" shaped with t...
2 comments posted 21yrs
posted by regor
2 comments posted 21yrs posted by regor

WAINSCOTING Paint or Stain?

I've completed the disassembly of a mirrored wall in a "dining room". The attached kitchen is pretty much all white and...
2 comments posted 21yrs
posted by BaaPRC-75
2 comments posted 21yrs posted by BaaPRC-75

Steve Knight plane + stones for sale

- Steve Knight wooden high angle coffin smoothing plane (regular iron), mint condition, $85 US - two 6 x 2 inch diamond...
5 comments posted 21yrs
posted by belkina
5 comments posted 21yrs posted by belkina

PUKEY YARD DUCKS

http://www.runnerduck.com/duck_family.htm OK, all you amateurs, this is for experienced woodworkers only. JOAT If it ain...
16 comments posted 21yrs
posted by Jakofalltrades
16 comments posted 21yrs posted by Jakofalltrades

Katrina plane giveaway 4 planes and counting.

A refresher for every 10.00 you donate you get entered into a drawing to win 1 of 4 planes. Send me a receipt of the do...
0 comments posted 21yrs
posted by stevek
0 comments posted 21yrs posted by stevek

Scraper to grit conversion

Maybe a silly question, but here goes. What is the equivalent grit in sandpaper terms for a scraper? After sanding to 2...
2 comments posted 21yrs
posted by .
2 comments posted 21yrs posted by .