Woodworking Forum

  1. Home
  2. Woodworking Forum
51629 Threads Posts
to

Worth reading in Woodworking Forum

cheapo mortising machine

I've seen 'em a lot in the catalogs and had a chance to try one. It seemed adequate for a tool I might use twice a year...
23 comments posted 20yrs
posted by edswoods.1
23 comments posted 20yrs posted by edswoods.1

Wooden Puzzles

You HAVE to check out these wooden puzzles... http://www.pacificpuzzleworks.com/The artist was featured on the Make Mag...
1 comments posted 20yrs
posted by alanv73
1 comments posted 20yrs posted by alanv73

disposable router bits - how safe?

I have used disposable router bits for some years. This is the type where the main shaft accepts disposable blades, usu...
3 comments posted 20yrs
posted by mretter
3 comments posted 20yrs posted by mretter

Building a small workbench - Advice needed

Hi everyone, I am planning to build a small workbench for my shop. The shop is only 8' x10', so space is at a minimum....
7 comments posted 20yrs
posted by rtgreen8972
7 comments posted 20yrs posted by rtgreen8972

SKIL Legend Challenge

So I just qualified for the SKIL Legend Challenge at Home Depot http://www.legendchallenge.ca. Has anyone ever done a ch...
4 comments posted 20yrs
posted by scott.n.jill
4 comments posted 20yrs posted by scott.n.jill

How long to dry freshly cut wood?

I have heard a rule of thumb for 1 year/inch. (I understand that is dependent on humidity, temperature, air circulation...
6 comments posted 20yrs
posted by Toller
6 comments posted 20yrs posted by Toller

cleaning a canister DC?

While changing my DC plastic bag, I noticed that the canister was caked with dust. I ran the brushes around a few times...
2 comments posted 20yrs
posted by Toller
2 comments posted 20yrs posted by Toller

Smoking Dremel Cut Out Tool

http://www.amazon.com/gp/product/B00005Q7B2/qid=1146679847/sr=1-2/ref=sr_1_2/103-7630343-9002247?%5Fencoding=UTF8&s=hi&...
4 comments posted 20yrs
posted by n
4 comments posted 20yrs posted by n

Peach flower (Tao of love).

i'm Chaim Ash, an architect from israel. This is two works in 3D graphics I've finished at last months. I suppose it co...
0 comments posted 20yrs
posted by chaim.ash
0 comments posted 20yrs posted by chaim.ash

Fir lumber load ratings?

How can I determine or lookup the load ratings or the load failure point for a fir plank that is 2 (1.5)" x 12 (11)" x...
5 comments posted 20yrs
posted by noxpurt
5 comments posted 20yrs posted by noxpurt

woodworker wanted

We're a twenty two year old business that moved into a 4300 sq ft. shop we purchased a year ago. Currently looking for...
1 comments posted 20yrs
posted by antons
1 comments posted 20yrs posted by antons

Stain won't dry - finishing question

Hi everyone, I have a solid pine coffee table top that I stained about 6 days ago. I wanted a dark stain so I laid it o...
4 comments posted 20yrs
posted by nin773
4 comments posted 20yrs posted by nin773

a cheap source for router bits ,all makes.

I found this source to be significant ly cheaper than most for all the major suppliers http://routerbitworld.com/ . I am...
2 comments posted 20yrs
posted by mikehide
2 comments posted 20yrs posted by mikehide

T-Force Air for nailers?

There are days when I do a lot of little things in a lot of different places and dragging a compressor (even a pancake)...
22 comments posted 20yrs
posted by design
22 comments posted 20yrs posted by design