Woodworking Forum

  1. Home
  2. Woodworking Forum
51629 Threads Posts
to

Worth reading in Woodworking Forum

OT - Cedar Wanna-Be Plank Salmon Results

As I mentioned a few weeks ago, I did a cedar-plank salmon bakeoff to determine the best cedar for cooking I only got t...
8 comments posted 20yrs
posted by no
8 comments posted 20yrs posted by no

Cleaning wooden Chess set

Hello, I have an old wooden chess set (circa 1940s). I think its made out of pine or boxwood. Its unpainted and the whi...
5 comments posted 20yrs
posted by sniper968
5 comments posted 20yrs posted by sniper968

How long to dry wood before paint?

I have pressure treated that I am going to solid stain. It was very wet. How long should it take to dry before It can be...
5 comments posted 20yrs
posted by trs80
5 comments posted 20yrs posted by trs80

Norms router station

Hello all. can anyone supply me with the dimensions for norms router table? tia
1 comments posted 20yrs
posted by bobthedog
1 comments posted 20yrs posted by bobthedog

OT - Jogging In A Jug

I just stopped by because I figured some of you OLD guys could use this info. I'm not old yet, but got bad joints, and...
10 comments posted 20yrs
posted by Jakofalltrades
10 comments posted 20yrs posted by Jakofalltrades

FS: Duck call parts

When I bought my pre-owned Delta 14" lathe, it came with various stuff to make duck calls. I've never done any turning...
7 comments posted 20yrs
posted by toddrf
7 comments posted 20yrs posted by toddrf

JET Bandsaw Riser Block

Hello 'Woodies'. . . Due to the overwhelming 'Spam Load' of several days ago, I 'dropped off' to get rid of it. The 'Ca...
1 comments posted 20yrs
posted by quahaug
1 comments posted 20yrs posted by quahaug

Book on Doors & Windows?

I've seen Taunton's offering on the subject, but it seems to be more focused on installation than fabrication. Does any...
0 comments posted 20yrs
posted by JayPique
0 comments posted 20yrs posted by JayPique

IPE Deck Finished!

What a weekend! 450 square feet of IPE deck on a new foundation to replace an old cedar structure that was rotting out,...
25 comments posted 20yrs
posted by xleanone
25 comments posted 20yrs posted by xleanone

Thick non-epoxy finish for table

I am building a small side table (30" semi-circle) with a surface covered with glued-on preserved leaves (The leaves ar...
4 comments posted 20yrs
posted by dromedaryl
4 comments posted 20yrs posted by dromedaryl

Craftsman Table Saw System and Ryobi BT3100

Are these two saws essentially the same item or copies of each other. The specs look very similar. If so, I assume the r...
1 comments posted 20yrs
posted by jfroche
1 comments posted 20yrs posted by jfroche

12 volt wood saw ideas ?

Looking to convert my large trailer into a mobile pallet recycling (into fuel) operation for next autumn (GB). Want the...
32 comments posted 20yrs
posted by david
32 comments posted 20yrs posted by david

looking for Recommendations on a lathe

I want to purchase a lathe for projects here in my wood shop. the price range is between $500 and $1000. I read on the...
12 comments posted 20yrs
posted by none
12 comments posted 20yrs posted by none

old plane

Have old block plane. It is stamped "w.thackeray planemaker ", remainder of stamp cannot be read. Mahogany body, brass c...
3 comments posted 20yrs
posted by norman
3 comments posted 20yrs posted by norman