Woodworking Forum

  1. Home
  2. Woodworking Forum
51625 Threads Posts
to

Worth reading in Woodworking Forum

dewalt announcement today.

News, not really. But they really need to be clear. First the guy references the 18volts. Then he starts calling them 2...
24 comments posted 10yrs
posted by nospam
24 comments posted 10yrs posted by nospam

whole write up on wood cork eglass laptop

the project for this caught my eye some time ago when the funding campaign started but just recently he did a whole wri...
5 comments posted 10yrs
posted by electric-comet
5 comments posted 10yrs posted by electric-comet

making enclosures for electronics

anyone done this how does the wood hold up over time i am not expecting a lot of heat as it is a low power device but i...
14 comments posted 10yrs
posted by electric-comet
14 comments posted 10yrs posted by electric-comet

Finishing the new shop floor

Based on previous comments I will be installing Advantech on 2X4 PT sleepers over concrete tomorrow. I expect it to tak...
30 comments posted 10yrs
posted by sw
30 comments posted 10yrs posted by sw

Cleaning/Enhancing Finish On Old (80+) Furniture

Happy Father's Day! We picked up a couple of pieces of bedroom furniture from Grandma's basement to use a starter furni...
16 comments posted 10yrs
posted by teamarrows
16 comments posted 10yrs posted by teamarrows

Table Saw Help

My portable (on site) 10" Hitachi table saw took a dump the other day. I disassembled the motor and discovered the wind...
46 comments posted 10yrs
posted by meanie.brat
46 comments posted 10yrs posted by meanie.brat

has live edge run its course

never really liked live edge but i see it all over the place some like it some do not years ago when i first saw live e...
18 comments posted 10yrs
posted by electric-comet
18 comments posted 10yrs posted by electric-comet

torsion top in the shop

at some point i need to make more work surface space i like the torsion top idea but not enough space for 4x8 i am thin...
18 comments posted 10yrs
posted by electric-comet
18 comments posted 10yrs posted by electric-comet

cheap source of mesh

at the grocery in the scouring pad section i found a pack of mesh sandpaper it was sold as scrubbing pads cheaper than...
0 comments posted 10yrs
posted by electric-comet
0 comments posted 10yrs posted by electric-comet

Need help with Jet JWTS-10JF

My husband is slowly upping his woodworking game. He has pretty much every other saw besides a good table saw. He has b...
4 comments posted 10yrs
posted by hansen.heather.k
4 comments posted 10yrs posted by hansen.heather.k

Sanding tree rings for viewing under a microscope

I currently use successive grits of sandpaper to smooth down the end g rain on wood cores for viewing tree rings down t...
35 comments posted 10yrs
posted by jcoruddat
35 comments posted 10yrs posted by jcoruddat

how long in the clamps

i do twenty four hours or more overnight is top vote getter http://www.thewoodwhisperer.com/poll/poll-how-long-before-re...
5 comments posted 10yrs
posted by electric-comet
5 comments posted 10yrs posted by electric-comet

new toy

More than a quarter century ago I bought a 3 1/2 HP Bosch 1611 router when I was making new cabinets for our condo prio...
1 comments posted 10yrs
posted by dadiOH
1 comments posted 10yrs posted by dadiOH

Food for thought

As mentioned in another post I am going to build a bed for a customer. This bed will require 2-60x60 1/2" thick sheets...
1 comments posted 10yrs
posted by lcb11211
1 comments posted 10yrs posted by lcb11211

DeWalt combination CSMS and TS

I received an e-mail from a trades publication and the reporter took a tour of a tool store in Germany. It was very int...
19 comments posted 10yrs
posted by lcb11211
19 comments posted 10yrs posted by lcb11211