Woodworking Forum

  1. Home
  2. Woodworking Forum
51629 Threads Posts
to

Worth reading in Woodworking Forum

Cutting hole in tile

I'm building a cabinet the will support a bathroom sink, one of those round dingies that sits on the cabinet. The cabin...
11 comments posted 19yrs
posted by jbushong65
11 comments posted 19yrs posted by jbushong65

saw blade

I have a Bosch 4000 ts. What would you suggest for a blade to make a smooth cut for picture molding? Patt
1 comments posted 19yrs
posted by pattj
1 comments posted 19yrs posted by pattj

veneer to sell

I have this veneers to sell: cherry, oak, maple, makore figure, walnut, beech, mahogany. I have many sequence sheet. Sh...
1 comments posted 19yrs
posted by sebasran
1 comments posted 19yrs posted by sebasran

New JET or Pioneer Cabinet saw?

Which would you buy a Jet or Pioneer Cabintet saw. Thanks Kevin
1 comments posted 19yrs
posted by kd4hee
1 comments posted 19yrs posted by kd4hee

PC Hammerdrill and oil

Hello All, I have recently purchased a "used" Porter Cable PC7751 hammer drill. I put the used in quotes because I purc...
0 comments posted 19yrs
posted by postbacktothegroup
0 comments posted 19yrs posted by postbacktothegroup

Shelf standard increments...

So I finally got my order from Outwater Hardware, no thanks to f'UPS pathetic delivery. Among the items I ordered were...
0 comments posted 19yrs
posted by aux3.DOH.4
0 comments posted 19yrs posted by aux3.DOH.4

Any Moldingknives.com users?

Has anyone here every ordered their Designer Knife Series? did it turn out to be something you used all the time or som...
0 comments posted 19yrs
posted by NoSpam
0 comments posted 19yrs posted by NoSpam

Cub Scout Krenovs

Jeff Thunder de cloaked and emerged from deep lurk mode to send me this stab from the past, in response to the recent C...
2 comments posted 19yrs
posted by notme
2 comments posted 19yrs posted by notme

Porter Cable #505 1/2 sheet sander

Hi all, I have a Porter Cable 505 half sheet sander and it has always been great to use. Lately it has been skating and...
1 comments posted 19yrs
posted by bstrawse
1 comments posted 19yrs posted by bstrawse

Bandsaw Vertical Drift! Help!!!

Hi, So I bought some 8/4 soft maple, with the thought that I could resaw it into 5/8" boards. I've got a 3 TPI 3/4" bla...
26 comments posted 19yrs
posted by Todd.Seidenberg
26 comments posted 19yrs posted by Todd.Seidenberg

Seeking Ideas on Trim

I plan to pull up carpeting and expose HW floors, and at the same time replace my baseboards. I also want to redo the s...
2 comments posted 19yrs
posted by jc_va
2 comments posted 19yrs posted by jc_va

what you might get for Xmas...

Luckily SWMBO doesn't buy me tools or might end up with one of these: http://www.amazon.com/gp/bestsellers/hi/ref=pd_ts_...
8 comments posted 19yrs
posted by NunyaBiznas
8 comments posted 19yrs posted by NunyaBiznas

Chair maker's pullshave - Lee Valley does it again

I pretty much quit hanging out in here a few years ago after the trolls showed up and made it more work than fun to rea...
4 comments posted 19yrs
posted by bbqboyee
4 comments posted 19yrs posted by bbqboyee

Advice for veneering a mantel

I'm making a mantel for our comtemporary fireplace. The Mantel is made up of MDF and is 3" inches thick. It sits in bet...
8 comments posted 19yrs
posted by brad.hammar
8 comments posted 19yrs posted by brad.hammar

FS: 6" x36" old Jointer in SW Florida

6" older cast iron jointer, in good condition. Knives were recently sharpened, Newer 110 volt motor. This jointer cuts...
0 comments posted 19yrs
posted by over40pirate
0 comments posted 19yrs posted by over40pirate