Woodworking Forum

  1. Home
  2. Woodworking Forum
51629 Threads Posts
to

Worth reading in Woodworking Forum

Amazingly Far OT - Steam Dragster

http://stanleysteamers.com/danville.htmJOATBugrit. Millennium hand AND shrimp.
0 comments posted 19yrs
posted by Jakofalltrades
0 comments posted 19yrs posted by Jakofalltrades

Kinda OT: making a square out of aluminum

Picked up the latest shopnotes and their is an artical about working with aluminum, making a square specificly. Accordi...
25 comments posted 19yrs
posted by Richard-N-0-S-Pam
25 comments posted 19yrs posted by Richard-N-0-S-Pam

another subpanel question

I'm installing a new subpanel for the new garage/shop. I decided to run a ground wire this time instead of trying to gr...
12 comments posted 19yrs
posted by brianlanning
12 comments posted 19yrs posted by brianlanning

Multi Master Tool

Has any of you guys tried this tool? I tried to view it at www.multimastertv.com but my webtv would not let me in. I di...
18 comments posted 19yrs
posted by Choctawman
18 comments posted 19yrs posted by Choctawman

FA: Forrest WWI, Duraliner, PC7518

Just listed a brand new Forrest WWI 10" Blade, Forrest 10" Duraliner Plywood, Melamine/Veneer blade and a nearly new Po...
0 comments posted 19yrs
posted by escarcegaNOSPAM
0 comments posted 19yrs posted by escarcegaNOSPAM

Tinting Shellac

What is the proper type of dye to use with shellac? I checked at Lowes and didn't see anything. Thanks in advance for an...
5 comments posted 19yrs
posted by ni4h
5 comments posted 19yrs posted by ni4h

Porter Cable Air Compressor

I'm going to buy my first air compressor/finish nailer combo kit and I was hoping for some advice/info. I see that both...
10 comments posted 19yrs
posted by dont
10 comments posted 19yrs posted by dont

Lumber yards near Charlotte, NC

I'm a woodworking hobbyist and up until now, I've been buying all my lumber at the big box stores. After giving my left...
4 comments posted 19yrs
posted by michael.billings
4 comments posted 19yrs posted by michael.billings

asian gate "roof"

Anyone have plans or designed/built an asian roof that typically covers a garden gate? Perhaps the folks in CA or Seatt...
3 comments posted 19yrs
posted by carruths
3 comments posted 19yrs posted by carruths

full extension slides for vertical partitions

I'm working on a project where I will have vertical partitions between two horizontal shelves. I want these partitions...
8 comments posted 19yrs
posted by brian
8 comments posted 19yrs posted by brian

Bleaching

Hi I have tried searching for bleaching but I seem to be getting conflicting information on the subject, I have made so...
12 comments posted 19yrs
posted by fionamallett
12 comments posted 19yrs posted by fionamallett

Best saw to cut plywood for furniture

I am building a desk from plywood, 1/2" and 3/4". I used a table saw and circular saw to rough cut after I marked the l...
23 comments posted 19yrs
posted by spydorbyte
23 comments posted 19yrs posted by spydorbyte

veneer to sell

I have this veneers to sell: cherry, oak, maple, makore figure, walnut, beech, mahogany. I have many sequence sheet. Sh...
0 comments posted 19yrs
posted by sebasran
0 comments posted 19yrs posted by sebasran

Wixey Digital Planer Gauge

Hello, I'm looking for some feedback on the Wixey Digital Planer Gauge that Woodcraft is currently selling for $44.99 u...
5 comments posted 19yrs
posted by pbogi
5 comments posted 19yrs posted by pbogi

Delta bandsaw motor replacement

A neighbor gave me a Delta model 28-185 band saw that the start capacitor was burned up on. He had removed it and no lo...
14 comments posted 19yrs
posted by crosseyedbarber
14 comments posted 19yrs posted by crosseyedbarber