Woodworking Forum

  1. Home
  2. Woodworking Forum
51629 Threads Posts
to

Worth reading in Woodworking Forum

jointer question

Hope you all don't mind me posting 2 questions in a row, but they seem to hit me in waves. My jointer, only when edge j...
8 comments posted 19yrs
posted by dserson
8 comments posted 19yrs posted by dserson

table saw fence question

I have a craftsman contractor saw. Despite opinions on the brand, this particular saw was reviewed with high regard for...
14 comments posted 19yrs
posted by dserson
14 comments posted 19yrs posted by dserson

The 'best' sealer/protection for a ber top

I've just stripped and restained an oak bartop, but I haven't put a finish on it yet. Before I do, what sort of finish/...
15 comments posted 19yrs
posted by tterrific
15 comments posted 19yrs posted by tterrific

sanding epoxy...

I am planning on gluing up some picture frames with West epoxy with wood dust filler. How well does the squeeze out san...
5 comments posted 19yrs
posted by Toller
5 comments posted 19yrs posted by Toller

Router Table suggestions...

Hi, All, I'm getting a new router table for my birthday (Good wives are nice to find!) but don't know what to get. I ha...
6 comments posted 19yrs
posted by cwo4cno7325
6 comments posted 19yrs posted by cwo4cno7325

Creating a pointed tip

I have a rod of wood about 1cm in diameter. I want to create an angled tip on it, but need it at certain angles, eg 40,...
3 comments posted 19yrs
posted by eliluong
3 comments posted 19yrs posted by eliluong

Material for homebuilt cabinets?

Hello, all! I've been lurking this group for a few weeks now, and many thanks for all the tips I've picked up so far. I...
42 comments posted 19yrs
posted by jlkilpatrick
42 comments posted 19yrs posted by jlkilpatrick

Dewalt nailers (or others??)

Folks, Can someone tell me the difference between the Dewalt 51844 and the 51845 air drive nailers? (These are the full...
6 comments posted 19yrs
posted by jcato
6 comments posted 19yrs posted by jcato

Boeshield

I just go t a new tablesaw. It has a cast ion top were my old one was aluminum. Using paste wax on the old one made it...
15 comments posted 19yrs
posted by cmagers
15 comments posted 19yrs posted by cmagers

Opinions on urethane (Gorilla) glue

It seems that most major marketers of wood glues are now selling their own brand of urethane glue. I've used Gorilla Gl...
8 comments posted 19yrs
posted by mike
8 comments posted 19yrs posted by mike

Completed Shuffleboard table

Hello all, For pictures of the completed shuffleboard table follow the link below: http://www.arealnice.com/shuffleboar...
6 comments posted 19yrs
posted by gkemper
6 comments posted 19yrs posted by gkemper

AIR LINES

I was into a Amish window factory the other day and their air lines caught my eye. They used 3" PVC pipe for all their...
44 comments posted 19yrs
posted by bill8vp
44 comments posted 19yrs posted by bill8vp

Biesemeyer fence?

Does Biesemeyer still make a rip fence drilled for older Craftsman table saws? Or is the hole pattern for Delta saws th...
9 comments posted 19yrs
posted by chuck94560
9 comments posted 19yrs posted by chuck94560

Conclusion to my "OOOPS!" Bandsaw Dilemma

Hey All, My welder friend was able to weld a steel rod onto the tip of the broken alignment pin to make a slap hammer a...
0 comments posted 19yrs
posted by duckbite
0 comments posted 19yrs posted by duckbite

Can twist be removed from carved panels?

My wife has been carving 2 16x32" panels made from 7/8" cherry that was air dried to
2 comments posted 19yrs
posted by eyeclinic
2 comments posted 19yrs posted by eyeclinic