Garage Door Tension Springs

I've never adjusted these. But, from what I've heard, they are very dangerous. Not something to do your self. They contain a LOT of energy, and can do tragic things and cause injuries.

That's my take on the matter, for what you paid for it.

Christopher A. Young Learn more about Jesus

Am I just a wimp?

Hi, If spring is broken it can be joined together with a small U bolt clamp and rewind it until replacement is ready. Once in a while I wipe the springs with oil soaked rag to prevent premature failure due to dry rubbing between coils which causes metal fatigue.

Many of the ones I have adjusted needed rods closer to 1/2 inch in diameter - REAL garage doors.

Talking about dangerous - - - I would STRONGLY caution EVERYBODY to ignore this advice. Attempting to clamp the spring will cause dangerous stresses, making the whole process (and door) much more dangerous. As for the oil - it just makes things dirtier and more difficult to work on - with virtually no advantage when it comes to the lifespan of the spring.

PERHAPS using a pair of clamps and overlaping more than half a coil

- so the clamps are 180 degrees apart MIGHT work - but the saddles of the clamps WILL interfere with the spring which would STILL make the situation un-necessarily dangerous.

That is what you think. I did that once until ordered spring ariivedm nothing happened. I installed oper, replaced spring, replace broken string, etc. on our garage door, nothing hapened to me or to the door. I am 100% safety concious person. I should take a picture of springs here and show if it collects dirt?, No it does not.

Have you ever done this? If not, don't assume and if so, then you did it wrong.

Were I work, we have several large overhead bay doors which are used daily and often. When one of the springs broke, it disabled the door. The door company we use often for door repair, frequently use the u-bolt clamp method while parts are on order. It doesn't endure anymore stress than in normal condition.

BTW, even a new pair of springs can break suddenly.

For many years, I always called in the pro. Then once, I tried it myself. I looked up on the Internet for methods, etc. The local Ace, of all places, carried the springs. After the 1st one, I could replace a spring in about an hour. Yes, the winding rods should be 1/2" as I recall. 2' long rods are probably too long. Mine are about 1' and give plenty of leverage even for winding the springs of a heavy, double wide door. BUT, IT CAN BE DANGEROUS if you are not careful as others have pointed out. BTW, one web site gave a good tip. Clamp a ViseGrip onto the pipe so that it will stop the pipe from turning. I know this won't stop the winding rods from flying around if you are not holding them when the set bolts are release, but it does keep things from moving. After reading the the horror stories, I was surprised at how little force it actually took to wind the springs. I was expecting much more. BUT, AS EVERYONE HAS SAID, IT CAN BE DANGEROUS if the rods get out of hand. If you feel hesitant, call a pro and watch and learn.

You did it and got away with it. It is NOT recommended - and NOT safe. I have worked on, adjusted, and replaced springs on at least a dozen different overhead doors with torsion springs.

And oiling ANYTHING makes it attract dirt. That is a GIVEN.

The door company I used ALWAYS had the required springs in stock. Where I worked we had SIX overhead doors that were upened and closed many times per day. Every spring and every fall we adjusted the door springs to compensate for the weight of the doors that changed with humidity - and every once in a while we had a spring break. I replaced one of those big suckers - and convinced the boss to call the door company for the next one. In the neighbourhood I've adjusted and replaced the springs on about a dozen garage doors - both tension and torsion. NO WAY would I attempt to "patch" the spring with cable clamps ("U" bolts). It's a case of get the door down, and leave it there untill the spring is replaced.

And if a NEW spring breaks, you are buying junk springs.

I'd be scared to death to use 1/4 rods. Check the holes - 1/2" if I remember, about 12" long. Be VERY prepared for the spring to unwind with a great deal of force if you release the two set screws.

Such a wonderful world it would be if everyone had all the items we need right when we need it.

To each his own. All I know is, it held up fine.

Tony-

I think what is hurting your credibility is suggesting the use of

I can state for a fact.... 1/4" rod runs the risk of damaging the torquing fitting, bending the rod or losing engagement.

OP-

If oyu read & understand the info in

and have decent mechanical abilities & aptitude you can fix the door yourself.

Working on the door yourself is not without risk but it is doable.

Wear safety glasses

cheers Bob

Did that, door man just left, lubricated and adjusted every thing, good as new again :-)

Thanks for all the suggestions and lively discussion.