Bought a Maytag top loader recently, model MVWB766FW1, off an appliance repair man. He'd put a new gearbox in it and that was a big part of why I went for it, plus the direct drive setup sounded solid. Paid $300 and it came with a 60-day warranty. It seems to run fine but the water level always looks low to me. My old washer let me pick the water level for every single load, and I'm guessing I was going through way more water than I actually needed. But at least everything got fully submerged and floated around while it washed. With this one I keep peeking under the lid and it's like the same clothes stay sitting on top the whole time it's running. Every time I want to say it needs more water, but part of me wonders if I've just been spoiled by old machines that guzzled it. So am I crazy, or is this worth bringing up with the guy I bought it from while the warranty still runs?
Is my Maytag washer using too little water or am I just used to the old way?
Nov 22, 2026
Last reply: 6 hours ago
5 Replies
Follow replies to this discussion?
First reply
You're not crazy, but you're also not seeing a defect. That machine is a high efficiency washer, and low water is just how they're designed to work. They clean with a lot less water on purpose, and the detergent actually works better that way. Think of it like stirring a…
Read the full replyInformation here may be outdated?
You're not crazy, but you're also not seeing a defect. That machine is a high efficiency washer, and low water is just how they're designed to work. They clean with a lot less water on purpose, and the detergent actually works better that way. Think of it like stirring a spoonful of lemon juice into a glass versus a bathtub. The same amount of soap in less water ends up more concentrated, so it does a better job on the clothes. The wash action in these machines is more like a washboard rubbing back and forth, so the clothes don't need to be floating around to get clean. Clothes sitting on top while the drum sloshes them around is normal, not a sign the machine is starving them. The adjustment from an old machine where you picked the level every load is real, though. I remember the first few loads in mine feeling wrong, like it couldn't possibly be doing anything in that little puddle. It takes some getting used to.
For the times you genuinely want more water, like towels, blankets, or other bulky stuff, look for a bedding, heavy duty, or bulky cycle, and check whether yours has a deep fill option. Those settings add water for large loads, which is the right call when you've got a big fluffy load that needs to move around more.
One more thing that'll help: use a detergent with enzymes in it. Something like Tide original liquid or the pods. These low water machines really do better with a decent detergent rather than the bargain stuff, because the enzymes are what break down the grime while the machine relies on concentrated soap and friction instead of a tub full of water.
So no, I wouldn't burn any of that warranty time on this. Save it for something that actually acts up.
The lid peeping is the part that got me too. I had an old machine where you picked the level every load, and for the first few weeks with my HE one I'd lift that lid constantly expecting to see a tub full of water. Eventually I just stopped checking and judged by results instead. Clothes come out clean and not dripping, so I figure the puddle is doing its job. Only thing I'd say is give the towels a shot on a bulky cycle before you decide anything, then compare how they come out against a regular wash. Did the repair guy happen to mention wheather yours has a deep fill option? That'd be handy to know for winter blankets.
The mental adjustment was the weirdest part for me too. My old machine had that little slider for the level and I never thought twice about it, so I get why yours looks wrong. Out of curiosity, did you check the control panel for a deep fill option? That's the first thing I'd poke at before bothering the guy you bought it from, since he'll just tell you the same thing everyone here did.
One distinction I'd make, and I say this as someone who squints at water levels more than is reasonable: what you're describing, the same items staying up top while the rest cycles underneath, is the machine moving things from the bottom rather than floating them, and it reads as wrong if you spent years setting the level yourself and watching everything bob around. A question for you though, does yours have the low flat plate at the bottom of the tub or an actual agitator post? The motion looks completely different between the two, and I'm curious which one yours has.
I'd take it easy on the assumption that the seller will just brush you off if you ask. He's a repairman who put a new gearbox in that machine himself, so he's got his own work on the line. If you called him up and said the water looks low and the same clothes stay on top the whole cycle, I'd bet he walks you through the cycles over the phone rather than tell you it's all in your head. Whether it changes anything is another matter, since it sounds normal, but asking him costs you nothing and the warranty clock is running either way.
Join the Discussion
Have something to add? Share your thoughts — no account required.
Didn't find your answer?
Ask the community — no account required