Woodworking Forum

  1. Home
  2. Woodworking Forum
51629 Threads Posts
to

Worth reading in Woodworking Forum

Melamine discovery

I don't usually work with melamine, but need to cut some closet parts. My normal blades, a WWII and a Freud, chip the e...
6 comments posted 18yrs
posted by DwightSchrute
6 comments posted 18yrs posted by DwightSchrute

LITTLE CANFIELD COFFER - PDF

http://www.currentmiddleages.org/tents/chest4canfield.pdf JOAT - who does not welcome thread question e-mails.. 10 Out...
0 comments posted 18yrs
posted by Jakofalltrades
0 comments posted 18yrs posted by Jakofalltrades

Corner chisel sharpening

I just got my Sorby 3/8 corner chisel delivered today and I need to hone it before I use it. I have used the scary shar...
5 comments posted 18yrs
posted by Rhonda
5 comments posted 18yrs posted by Rhonda

JJ-8 jointer

Assuming flat and coplaner tables -- anything else to look for on an older jointer? Any know issues with a JJ-8 ? It lo...
1 comments posted 18yrs
posted by NOSPAM_coloradotrout
1 comments posted 18yrs posted by NOSPAM_coloradotrout

New Dewalt Saw - Dewalt Support Response

Hello David, and thanks for using DEWALT's on-line support. At this time there are no plans to introduce this saw to th...
3 comments posted 18yrs
posted by very_dirty_dave
3 comments posted 18yrs posted by very_dirty_dave

MD WW Show - response to my email

I sent an email to The Woodworking Shows folks complaining about 2 main issues I saw at the recent Timonium show, and h...
10 comments posted 18yrs
posted by no-one
10 comments posted 18yrs posted by no-one

ot: For the under 30 crowd

THE SPOILED UNDER 30 CROWD!!! If you are 30 or older you will think this is hilarious!!! (Please forgive some of the la...
0 comments posted 18yrs
posted by skipwill
0 comments posted 18yrs posted by skipwill

Camouflaging sap wood in red oak

I recently acquired several hundred bd ft of red oak from a neighbor. This deal was consumated with the understanding a...
5 comments posted 18yrs
posted by smeier07NOSPAM
5 comments posted 18yrs posted by smeier07NOSPAM

Source for dyed (green) bottle stopper blanks

My regular (and favorite) supplier Arizona Silhouette is out of the green bottle stopper blanks (in both boxelder and M...
32 comments posted 18yrs
posted by Nobody
32 comments posted 18yrs posted by Nobody

Silicon/sealant dispenser review

I install a lot of separate back splashes. In laminates, and solid surface. Also, I seal countertops around walls etc....
0 comments posted 18yrs
posted by Counterfitter
0 comments posted 18yrs posted by Counterfitter

Hotmelt adhesive gun review.

I use hotmelt adhesive a lot in my shop. Never as a permanent solution, but as a clamp, extra hand, for something fast....
9 comments posted 18yrs
posted by Counterfitter
9 comments posted 18yrs posted by Counterfitter

The new Paul Bunyan

http://www.youtube.com/watch?v=Ei9LlLLZwAU
2 comments posted 18yrs
posted by dlwinterburn
2 comments posted 18yrs posted by dlwinterburn

In between projects AND Cast_Iron_Protection

I started spraying a coat of T-9 Boeshield on my cast iron tops and letting it dry (unwiped). When I am ready to use th...
22 comments posted 18yrs
posted by .
22 comments posted 18yrs posted by .

The Rotex, A review.

Well what can I say? Thank you Charlieb and Robatoy for getting me started on the slipper slope with Festool tools. I s...
1 comments posted 18yrs
posted by removespamlcb11211
1 comments posted 18yrs posted by removespamlcb11211