Woodworking Forum

  1. Home
  2. Woodworking Forum
51625 Threads Posts
to

Worth reading in Woodworking Forum

Cost Reduced Freud SD208 Dado Set

I bought a Freud SD208 dado set from Rockler earlier in the week. It was locked in a glass cabinet and I didn't take a...
1 comments posted 17yrs
posted by albert6
1 comments posted 17yrs posted by albert6

Iturra Design?

I haven't been able to reach Iturra Design to place an order. Any idea what's going on with them?
0 comments posted 17yrs
posted by boat042-nospam
0 comments posted 17yrs posted by boat042-nospam

Table Saw Blade won't Tighten

I have a Ridgid TS2424 table saw, that, up until today I have been very happy with. But today the following happened wh...
72 comments posted 17yrs
posted by mrmarty
72 comments posted 17yrs posted by mrmarty

New Grizzly cabinet saws

I am thinking about replacing my old (original Artisan 63) contractor saw with a Grizzly cabinet saw. I have had fine r...
3 comments posted 17yrs
posted by wilson
3 comments posted 17yrs posted by wilson

Sketchup - FWIW - Plugins for woodworkers

Strictly FWIW: A couple of woodworking specific plug-ins that may be of interest can be downloaded at: http://www.sketc...
3 comments posted 17yrs
posted by kac
3 comments posted 17yrs posted by kac

Freud router

I popped for the $99 Freud on sale on Woodcraft and must say I'm disappointed. Here's why: 1. There's way too much slop...
8 comments posted 17yrs
posted by nospam
8 comments posted 17yrs posted by nospam

My future is PM66, but Ridgid for now?

Hi, I'm a starting woodworker. I've done a lot of research and I think that there is a PM66 in my future. But right now...
6 comments posted 17yrs
posted by aaronfude
6 comments posted 17yrs posted by aaronfude

5/16 carriage bolt 6 1/2 inches long

I need a stainless steel full thread 5/16 carriage bolt 6 1/2 inches long. My local Lowes nor Home Depot have them. I t...
17 comments posted 17yrs
posted by sam
17 comments posted 17yrs posted by sam

LP Air in the shop

Looking for ideas on how to distribute LP air in my shop. My shop is 18' X 22' and I have a stair case in the back corn...
27 comments posted 17yrs
posted by neillarson
27 comments posted 17yrs posted by neillarson

Skill with a Skill

Framing crew on a current construction project is being run by two union carpenters from Washington state. Both of thes...
53 comments posted 17yrs
posted by kac
53 comments posted 17yrs posted by kac

advice on this particular piano bench

Hi, I wonder if any of chaps could take a look at this plan for a Mission style piano bench: http://vintageinternetplan...
7 comments posted 17yrs
posted by largecorp
7 comments posted 17yrs posted by largecorp

Speaking of Minwax Tung Oil Finish

I making and end table and wonder if a Minwax Tung Oil Finish of 3 to 5 coats will give me a waterproof finish that wil...
5 comments posted 17yrs
posted by kennerman1
5 comments posted 17yrs posted by kennerman1

Dust collection question

I still have my fancy new 2HP Grizzly Cyclone set up and ready to go, but with no ductwork installed. I borrowed the bo...
10 comments posted 17yrs
posted by bbqboyee
10 comments posted 17yrs posted by bbqboyee

knife hinges

I'm looking for a knife hinge that will allow 8" wide overlay cabinet doors to be opened completely and fold back along...
14 comments posted 17yrs
posted by grossboj.nospam
14 comments posted 17yrs posted by grossboj.nospam

Hello all, my name is Rob. I stained some cherry.

A fireplace mantle I am working on for the HomeShow. This is just 1/3 of the whole thing. It shows the detail that the...
11 comments posted 17yrs
posted by Counterfitter
11 comments posted 17yrs posted by Counterfitter