Woodworking Forum

51629 Threads Posts
to

Re: Counter Top Replacement for Glass Desk

> I've had very good luck with blackboard slate. It is easy to cut, easy > to clean, & makes a super nice work surface....
0 comments posted 22yrs
posted by winkgz
0 comments posted 22yrs posted by winkgz

Nail Puller Questions

I want to pull nails from wood pallets. Yeah, I probably already know all the ways you'll suggest already, drilling, cu...
19 comments posted 22yrs
posted by Jakofalltrades
19 comments posted 22yrs posted by Jakofalltrades

Semi OT - Rub Blocks and Doves

This morning, on one of my many trips between the shop and the house, I saw the little dove on my path. There are two o...
0 comments posted 22yrs
posted by charlieb
0 comments posted 22yrs posted by charlieb

Honduras mahogany

Anyone know of a source of Honduras mahogany in the southeast ....??? mjh -- http://members.tripod.com/mikehide2
5 comments posted 22yrs
posted by mikehide
5 comments posted 22yrs posted by mikehide

Entry door page update

I received some questions and a request after posting here about an entry door I made last winter, so I spent some time...
4 comments posted 22yrs
posted by jwilson
4 comments posted 22yrs posted by jwilson

Coping and Sticking Bits set?

Hi everyone, I am making some doors and wondered if anyone knew where I could get a matched set of coping and sticking...
4 comments posted 22yrs
posted by Google1
4 comments posted 22yrs posted by Google1

Re: Best material to make built-in desk?

Dear Chris, The choice of desk wood depends on the look you want and your budget. All woods can work in one form or ano...
4 comments posted 22yrs
posted by jriley
4 comments posted 22yrs posted by jriley

Advice needed on new compressor setup

Greetings, Our factory recently purchased a 20HP Kaeser rotary screw SK26 model. It was used with 800 hours total on it...
2 comments posted 22yrs
posted by deja
2 comments posted 22yrs posted by deja

Old Delta 18" Wedge Bed Planer

Were the old Delta 18" wedge bed planers good? One concern I have is the fixed pressure bar design. My 12" Powermatic h...
4 comments posted 22yrs
posted by calbert7
4 comments posted 22yrs posted by calbert7

Re: need to oxidize some wood -- how?

Alan W schreef > In order to deepen the purple on the jewelry box, especially the sides as they are staying the brown v...
0 comments posted 22yrs
posted by dipteryx
0 comments posted 22yrs posted by dipteryx

Planer Knife Locking Bar Design

I need to make some planer knife locking bars. Does anyone know anything about the design of these? I drew some various...
1 comments posted 22yrs
posted by calbert7
1 comments posted 22yrs posted by calbert7

Re: Watco Wax finish

>Anyone use this? Looks promising as a great finish for some indoor benches >I'm building. One question is there's a na...
0 comments posted 22yrs
posted by jpaquay
0 comments posted 22yrs posted by jpaquay

PADE Tenoner?

Anyone have a manual for the PADE tenenor
1 comments posted 22yrs
posted by otf70
1 comments posted 22yrs posted by otf70

Shop built horizontal mortising table question

Hello All: I am thinking of building a horizontal mortising table similar to the ones made by Multi-router and by Inca....
4 comments posted 22yrs
posted by jmartinNO
4 comments posted 22yrs posted by jmartinNO

Re: Is naphtha safe for thinning oil to spray????

FWIW I know of a couple paints/primers that are naphtha based. Zinsser has a fast dry stain blocking primer, Sherwin Wi...
0 comments posted 22yrs
posted by blackmREMOVEoriah
0 comments posted 22yrs posted by blackmREMOVEoriah