Woodworking Forum

51629 Threads Posts
to

Safe to use 10" blade in a 12" saw?

Is it safe to use 10" blades in a 12" miter saw? I have some nice 10" blades I would hate to see go to waste. Pete http...
11 comments posted 22yrs
posted by pistoleer
11 comments posted 22yrs posted by pistoleer

Brazilian Rosewood

Hello I am starting a new project soon. the plans call for Brazilian Rosewood . the problem is none is available. so I...
24 comments posted 22yrs
posted by crashdad
24 comments posted 22yrs posted by crashdad

really minor gloat

Tool sale advertised in the area this week. Most of the stuff was junk but picked up 16 spreader clamps, four 8", eight...
0 comments posted 22yrs
posted by gibsonr.dontneedspam
0 comments posted 22yrs posted by gibsonr.dontneedspam

How do finish water based poly from Compliant?

I would like to fine sand the finish and then polish and buff the finish. What size grit sand paper should be started an...
14 comments posted 22yrs
posted by cijn
14 comments posted 22yrs posted by cijn

Particle board/Melamine Screws

I need to fasten some steel brackets to the face of 3/4" melamine. Anyone have some suggestions for the type of screw,...
5 comments posted 22yrs
posted by denaas
5 comments posted 22yrs posted by denaas

Hand planing better

Now that I have a small collection of handplanes, I need to make my bench a little more planing friendly. Currently I u...
26 comments posted 22yrs
posted by emptyshell
26 comments posted 22yrs posted by emptyshell

Question about the GRR-Ripper

I was wondering if any of you here bought and tried the GRR-Ripper. Any positive comments? I'm pondering getting one fo...
20 comments posted 22yrs
posted by none
20 comments posted 22yrs posted by none

A minor gloat

Tool sale advertised in the area this week. Most of the stuff was junk but picked up 16 spreader clamps, four 8", eight...
0 comments posted 22yrs
posted by gibsonr.dontneedspam
0 comments posted 22yrs posted by gibsonr.dontneedspam

Re Lee Valley plane question

I bought a Mujingfang plane (chinese not Taiwanese) that has a 50 degree bed angle for around $30. I purchased it based...
4 comments posted 22yrs
posted by srazor
4 comments posted 22yrs posted by srazor

Does this count as a Gloat?

http://www.klownhammer.org/photos.RAS.jpgOh, it's in perfect working condition and it was... ___ ___ ___ ___ |||| | __|...
6 comments posted 22yrs
posted by paddyolguin
6 comments posted 22yrs posted by paddyolguin

HF is coming! HF is coming!

Okay, okay . . . I'd be a lot more excited (and my checking account far more in jeopardy) if Rockler or Lee Valley were...
13 comments posted 22yrs
posted by kbcraig
13 comments posted 22yrs posted by kbcraig

Looking for someone to install hardwood floors

Hi. I'm looking for someone to install hardwood floors the "right" way. :o) I'm in Northern Jersey and have a business...
2 comments posted 22yrs
posted by dwhite110
2 comments posted 22yrs posted by dwhite110

Figuring out angle of a cut using "rise over run"?

Hi all, I'm really new to woodworking. In fact, I haven't really done any yet. However, I am laying my own wood floor (...
19 comments posted 22yrs
posted by bkjones
19 comments posted 22yrs posted by bkjones

FA: curly maple veneer strips

http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&rd=1&item=8131887998 -- Regards, Doug Miller (alphageek-at-milmac-dot-com...
0 comments posted 22yrs
posted by spambait
0 comments posted 22yrs posted by spambait

Christmas ideas

I am looking for some suggestions for easy to make Christmas presents. Preferably something that can be a 'family' gift...
9 comments posted 22yrs
posted by notareal
9 comments posted 22yrs posted by notareal