Woodworking Forum

  1. Home
  2. Woodworking Forum
51629 Threads Posts
to

Worth reading in Woodworking Forum

Countertop laminate success

I tried something I had never done before: relaminating my kitchen countertop with formica right over the old stuff. Th...
8 comments posted 21yrs
posted by mextex1
8 comments posted 21yrs posted by mextex1

220v extension cord for Table saw?

I am considering getting a 220 volt table saw but have 220 volt available at the entrance to my garage and would have t...
53 comments posted 21yrs
posted by mextex1
53 comments posted 21yrs posted by mextex1

FS: Jesada Cutters

Hello All- Yes, I am still working to sell off the rest of the cutters that I have left. As I had listed before, I am a...
1 comments posted 21yrs
posted by msgtwins
1 comments posted 21yrs posted by msgtwins

Harbor Freight 14" bandsaw motor mount question

For those of you who have assembled this saw -- the motor mount seems to have contradictory instructions (what a surpri...
3 comments posted 21yrs
posted by robdew
3 comments posted 21yrs posted by robdew

Air Hockey Table - Plans

My Grandson would love his grandpa to make him an "Air Hockey Table" I do not have any proven plans but could no doubt...
4 comments posted 21yrs
posted by Nobody
4 comments posted 21yrs posted by Nobody

Woodworking stuff to see in Australia?

Hello All: I will spend most of December in Sydney, Brisbane, and Canberra. Can any of you suggest woodworking related...
3 comments posted 21yrs
posted by jmartinNO
3 comments posted 21yrs posted by jmartinNO

There is always some way to screw up

I am making a box jointed organizer. I didn't think it mattered how I assembled the sides (as long as I had the grove f...
11 comments posted 21yrs
posted by toller
11 comments posted 21yrs posted by toller

Flush trimming work top

I have now completed construction of my workbench top -- 2 sheets of 3/4" mdf laminated together and edge banded. I now...
14 comments posted 21yrs
posted by mfwebb
14 comments posted 21yrs posted by mfwebb

Router Table setup..

Hi, I am about to build a router table, but I am unsure of how you change the bit whilst it's in the table. It sounds l...
7 comments posted 21yrs
posted by anglersam
7 comments posted 21yrs posted by anglersam

Is it normal to have to flatten flattening stones?

I picked up a pair of Ice Bear flattening stones which are quite out of flat themselves. Is it normal for flattening st...
15 comments posted 21yrs
posted by missed-spam
15 comments posted 21yrs posted by missed-spam

F/S equipment

Selling Hendy Lathe 16 x 54 $2500,single lip cutter grinder $650,email for info and snipped-for-privacy@aol.com
0 comments posted 21yrs
posted by NTDTOOL4U
0 comments posted 21yrs posted by NTDTOOL4U

Bob Vila

-------------------------------------------------------------------------------- Posted on Sun, Nov. 28, 2004 On the Ho...
13 comments posted 21yrs
posted by notme
13 comments posted 21yrs posted by notme

Mitring Corners

Hi, I would like to try and make a small mitred box. I am unsure though how you clamp / hold a joint whilst glued. Also,...
10 comments posted 21yrs
posted by anglersam
10 comments posted 21yrs posted by anglersam

Silver Maple any good?

I have some land that has open space that I plan to plant trees on for eventual use in my shop. I enjoy working with ma...
24 comments posted 21yrs
posted by nospam
24 comments posted 21yrs posted by nospam