Woodworking Forum

  1. Home
  2. Woodworking Forum
51629 Threads Posts
to

Worth reading in Woodworking Forum

Carbide Blade Sharpening Service

Previous posting have mentionned returning carbide blades to Freud for sharpening. In checking with Freud, this service...
3 comments posted 21yrs
posted by pdulong
3 comments posted 21yrs posted by pdulong

Milwaukee 18v batteries

Hi: Has anyone else had problems with short life on Milwaukee 18v 2.4amp batteries? I have had two go dead in less than...
13 comments posted 21yrs
posted by ole
13 comments posted 21yrs posted by ole

Electrical help: 20 amp vs 30 amp

I had an electrical question a few months ago about this, and got several varied responses - mainly because I did not h...
62 comments posted 21yrs
posted by loutent
62 comments posted 21yrs posted by loutent

beeswax as grease

I was looking all over, auto parts stores, online sites, searches for "petroleum based grease" among other terms... poi...
27 comments posted 21yrs
posted by ahem
27 comments posted 21yrs posted by ahem

Motor mount for F56

I'm attempting to build a thickness drum sander, and the motor I bought has a mount called an F56C. Basically, if you'r...
3 comments posted 21yrs
posted by larrybud2002
3 comments posted 21yrs posted by larrybud2002

unisaw table alignment

I have unisaw that I can't seem to get into alignment. When I loosen or remove the trunnions and push the back of the t...
15 comments posted 21yrs
posted by trevorborgmeier
15 comments posted 21yrs posted by trevorborgmeier

looking

Im looking to meet a lady for conversation and friendship e mail me
12 comments posted 21yrs
posted by singlenlookn
12 comments posted 21yrs posted by singlenlookn

Wow! Harder than I imagined

I finally got a stacked dado set and for my first project it was my intent to construct a box jointing jig. Turned out...
24 comments posted 21yrs
posted by chuck94560
24 comments posted 21yrs posted by chuck94560

Robin lee, tech question

Gotta install question. Stock #00k50.90 and #00k50.95 - Door dampers. What is the recommended install position of these...
9 comments posted 21yrs
posted by I'm
9 comments posted 21yrs posted by I'm

finish for wood shelves for clothes

I'm planning my first woodworking project - a set of shelves in our walk-in bedroom closet. 5 shelves each about 4.5' x...
16 comments posted 21yrs
posted by mcommushroom
16 comments posted 21yrs posted by mcommushroom

Unisaw lube?

My Uni's finally getting a bit "cranky" when I apply the cranky. I've got T-9 but not sure that's the best product to lu...
14 comments posted 21yrs
posted by David
14 comments posted 21yrs posted by David

Bandsaw blades 80'?

This summer I purchased a used Craftsman bandsaw only to find out recently when I went to purchase blades that no one c...
9 comments posted 21yrs
posted by NoSpam
9 comments posted 21yrs posted by NoSpam

How to fix squeaky wood?

Whenever I open or close the drawers in my dresser, it gives off this horrible squeak. Is there some kind or lubricant o...
12 comments posted 21yrs
posted by haha
12 comments posted 21yrs posted by haha

Ryobi, why no demand for it?

Looking over Ebay auctions, I noiced that Ryobi tools are going for way less than other brands and most don't have any...
35 comments posted 21yrs
posted by hsiacc
35 comments posted 21yrs posted by hsiacc

Bandsaw Conversion

A friend of mine wants to sell me an 18" Craftsman bandsaw for 200.00. It's a metal-cutting only bandsaw, and has never...
11 comments posted 21yrs
posted by bub209
11 comments posted 21yrs posted by bub209