Woodworking Forum

  1. Home
  2. Woodworking Forum
51629 Threads Posts
to

Worth reading in Woodworking Forum

PERPETUAL WALL CALENDAR

http://www.uniqueprojects.com/projects/perpetual/perpetual.htm I wouldn't make one. I like calendars you can write doct...
1 comments posted 21yrs
posted by Jakofalltrades
1 comments posted 21yrs posted by Jakofalltrades

CHIPPENDALE WINDOW BOX

http://netscape.bhg.com/bhg/story.jhtml?storyid=/templatedata/bhg/story/data/12456.xml&catref=cat820068JOATCharity ain'...
1 comments posted 21yrs
posted by Jakofalltrades
1 comments posted 21yrs posted by Jakofalltrades

What color to paint workshop

I'm insulating the walls in my garage/workshop and just realized that I'll need to paint the drywall when finished. So...
44 comments posted 21yrs
posted by witczak
44 comments posted 21yrs posted by witczak

MS Safety - cutting thin-strip miters (whew!)

I'm sure that this has been discussed before, but when I did a search, I did not find anything specific. I made a pair...
11 comments posted 21yrs
posted by loutent
11 comments posted 21yrs posted by loutent

Delta 6" jointer

I bought a used 6" delta jointer but it is not the one shown on the delta website. Was there an older 6" model which is...
9 comments posted 21yrs
posted by habbi
9 comments posted 21yrs posted by habbi

Bill Ding plans

I had a request today for these plans that I had made available on my web site. I inadvertently removed them during a re...
0 comments posted 21yrs
posted by dave
0 comments posted 21yrs posted by dave

Not all 1/4 " hardboard is 1/4"

I just found out that the drill press table I made last week to include a vac channel for sanding is almost useless. La...
11 comments posted 21yrs
posted by nospam.nospam.com
11 comments posted 21yrs posted by nospam.nospam.com

Learned something...

The project I've been working came to a halt the other day. The first drawer - which was verified to be square and stra...
14 comments posted 21yrs
posted by chuck94560
14 comments posted 21yrs posted by chuck94560

Anyone actually using a Rigid BS1400?

I got some HD gift cards and I saw this unit for $299 at HD. Just wondered if anyone had any practical experience with...
8 comments posted 21yrs
posted by captmikey
8 comments posted 21yrs posted by captmikey

How to calculate drive wheel size?

If a shaft is turning at about 800rpm and you want to use a drive wheel to friction spin a 12" disk at 30rpm what size s...
6 comments posted 21yrs
posted by address
6 comments posted 21yrs posted by address

Question about (lack of) heat in the basement workshop

It is 50 degrees in my basement workshop today which means too cold to do any gluing and probably too cold to cut miter...
24 comments posted 21yrs
posted by REMOVE-dicksnyder
24 comments posted 21yrs posted by REMOVE-dicksnyder

Old Skil sander belt size?

I have an old "Skil" model 324 belt sander, and I would like to get some sanding belts for it. The one that was on it m...
5 comments posted 21yrs
posted by toolmiser
5 comments posted 21yrs posted by toolmiser

Which end to put the tails on?

When cutting through dovetails on a rectangular piece, are there any conventions on what side (long 'side' or shorter 'e...
4 comments posted 21yrs
posted by brian_j_roth
4 comments posted 21yrs posted by brian_j_roth

Table saw arbor adapte

Does anybody know where I can buy a 5/8ths arbor adaptor for a 30mm tablesaw blade? I can't seem tofind anything on the...
2 comments posted 21yrs
posted by nospam
2 comments posted 21yrs posted by nospam