Woodworking Forum

  1. Home
  2. Woodworking Forum
51629 Threads Posts
to

Worth reading in Woodworking Forum

Scary Mag Starter Sw Failure = HAND-burger

Folks - Okay, since the TS mishap last summer and my conversion into a "Safety Saint" - it has paid off, blade protecti...
15 comments posted 21yrs
posted by johnmoorhead
15 comments posted 21yrs posted by johnmoorhead

Woodworker's Journal: Yea or Nay?

I already get Wood, Fine Woodworking, & American Woodworker. Is WWJ a fine addition to those, or an also-ran. I'm sure...
26 comments posted 21yrs
posted by David
26 comments posted 21yrs posted by David

Finish for garden bench

I have built a rustic looking garden bench out of cedar and I now need to finish it. It needs some kind of stain to uni...
5 comments posted 21yrs
posted by jackfe
5 comments posted 21yrs posted by jackfe

Concrete pigment as a woodstain?

I was wondering if anyone had tried this. I'm wondering how it would mix up in a clear wood stain base. I like the colo...
5 comments posted 21yrs
posted by MHaldorson
5 comments posted 21yrs posted by MHaldorson

Outdoor play systems/swingsets you have built?

Hi, I am going to start planning a play system to build for my son this summer. I have looked at some home centers and...
6 comments posted 21yrs
posted by circusfreak
6 comments posted 21yrs posted by circusfreak

platfrom bed plands

i am looking for plans for a platfrom bed does and body have one or know were i mite be able to get one
0 comments posted 21yrs
posted by bobbieandpaul
0 comments posted 21yrs posted by bobbieandpaul

Perfect Stain Match

I want to thank everyone who replied to my earlier thread about making a stain to match my existing kitchen oak cabinet...
1 comments posted 21yrs
posted by nekias
1 comments posted 21yrs posted by nekias

HBTM

Folks - Well I woke up this morning, and sung a little sonnet to my wif... "Happy Birthday to ME! I love my ROSIE, I'm...
3 comments posted 21yrs
posted by johnmoorhead
3 comments posted 21yrs posted by johnmoorhead

bent plywood lamination help in Seattle area

Hi, I am looking for some help and advice on a bent plywood lamination furniture project. I have a design and the means...
6 comments posted 21yrs
posted by nlbauers
6 comments posted 21yrs posted by nlbauers

Elliptical leg

Hi, I need (well, would like) one elliptical leg for the end of an elliptical table. The other end will be attached to...
39 comments posted 21yrs
posted by mare*Remove*All*0f*This*I*Hate
39 comments posted 21yrs posted by mare*Remove*All*0f*This*I*Hate

redwood fence post fix

We have a small (8 section) basketweave fence that's been around for 40+ years. I recently reworked several of the pane...
13 comments posted 21yrs
posted by b26440510
13 comments posted 21yrs posted by b26440510

Anyone use Steve Wall Lumber in N.C.

Hello, Has anyone ever used Steve Wall Lumber (www.walllumber.com)? The prices are quite good, as compared to my area....
7 comments posted 21yrs
posted by cblood59
7 comments posted 21yrs posted by cblood59

Setting up TS Extension Wing

Hi all. I spent a last night putting together my new TS and ran into a snag. I am having trouble getting the cast exten...
10 comments posted 21yrs
posted by stickler.iv
10 comments posted 21yrs posted by stickler.iv

wood type

Going to replace widow sill, seeking best wood to use. Desire to retain natural wood finish (or stain) Protective coatin...
1 comments posted 21yrs
posted by dpettit
1 comments posted 21yrs posted by dpettit

PING: Charlie Self

Charlie, I was wanting to write an article-type piece on a guy and was wondering if you could advise. This isn't for pr...
0 comments posted 21yrs
posted by phildcrowNOSPAM
0 comments posted 21yrs posted by phildcrowNOSPAM