Woodworking Forum

  1. Home
  2. Woodworking Forum
51629 Threads Posts
to

Worth reading in Woodworking Forum

damaged finish on expensive wood table

Hello afficiandos, Pardon my ignorance as a newbie. I ended up putting a leaking battery onto my ralph lauren coffee ta...
2 comments posted 21yrs
posted by vivekgauri
2 comments posted 21yrs posted by vivekgauri

Tired of electrical discussions.

This is not intended to create a flame war. I am deeply concerned about the blatant misinformation being written by a s...
53 comments posted 21yrs
posted by design
53 comments posted 21yrs posted by design

End grain gluing.

I have to make an interior window ledge that is 13.5 feet long. I am using Peruvian Walnut, and the longest boards I ca...
22 comments posted 21yrs
posted by eric_blair
22 comments posted 21yrs posted by eric_blair

Rewiring this old Crafstman Bench saw???

As I posted earlier, I'm setting up an old Craftsman 10" bench saw I inherited. This will be a big improvement over the...
18 comments posted 21yrs
posted by junkspam
18 comments posted 21yrs posted by junkspam

sliding compound miter saws

I am in the market for a new 12" sliding compound miter saw. I have been using a DeWalt for about the last 10 years and...
1 comments posted 21yrs
posted by cjscurria
1 comments posted 21yrs posted by cjscurria

UK supplier of Cherry and Oak

Hi all. I'm looking to find a supplier of Cherry and Oak in the UK. I can find lots of timber suppliers but they all se...
3 comments posted 21yrs
posted by jeffh
3 comments posted 21yrs posted by jeffh

Source for Thick Walnut

Anyone know of a source for Kiln-dried 8/4 or thicker walnut in the SE Kansas, SW Missouri, NW Arkansas, NE OK area? Ron...
6 comments posted 21yrs
posted by rbrogan
6 comments posted 21yrs posted by rbrogan

Circular saw won't ground, safe?

Is it safe to operate an all alloy housing circular saw. My 15-year old industrial saw is reliable but the only thing a...
105 comments posted 21yrs
posted by bravecat
105 comments posted 21yrs posted by bravecat

Joints and Hinges

I am seekinf a rotating joint so I could swivel (non wheels) a model I am making. It would be like a model skeleton, I...
3 comments posted 21yrs
posted by teak
3 comments posted 21yrs posted by teak

Good Books on DIY tools

I have decided to start doing a bit of DIY but to tell the truth I'm sixty+ and yes, I know it's a bit late to try and...
7 comments posted 21yrs
posted by
7 comments posted 21yrs posted by

Woodturners

Is there a woodturners newsgroup? Tim
11 comments posted 21yrs
posted by tdup2
11 comments posted 21yrs posted by tdup2

abernathy vise

I picked up an Abernathy Vise No. 80D at a yard sale today. Twenty bucks. The seller had cleaned it up and painted it y...
8 comments posted 21yrs
posted by bobthebuilderyeshecan
8 comments posted 21yrs posted by bobthebuilderyeshecan

2101 brace, my first

...and man is it well made. I had read in here and out on the 'net that these are the best ever made, I quite believe i...
1 comments posted 21yrs
posted by ahem
1 comments posted 21yrs posted by ahem

restoring teak veneer table

I have acquired a table that is teak veneer over particle board. It's an OK table but there are gouges in the veneer wh...
2 comments posted 21yrs
posted by FFf
2 comments posted 21yrs posted by FFf