Woodworking Forum

  1. Home
  2. Woodworking Forum
51629 Threads Posts
to

Worth reading in Woodworking Forum

Grump, grump, argh! Lost hardware.

Back in April, I bought some hardware for a possible book proposal. As usual, Lee Valley got it here so fast I barely h...
10 comments posted 21yrs
posted by charliediy
10 comments posted 21yrs posted by charliediy

Guitar Case

I am thinking of making some guitar cases. I have looked on the net and googled and could not fine plans anywhere. Does...
5 comments posted 21yrs
posted by NOSPAM-miamited
5 comments posted 21yrs posted by NOSPAM-miamited

O.T. - Grand Junction, Colorado

Grand Junction, Colorado Considering a move there . . . Are there any woodworking clubs, suppliers for material or tools...
4 comments posted 21yrs
posted by no_spam_4_me
4 comments posted 21yrs posted by no_spam_4_me

Veneer 3/8" radius w/ paper-backed ash?

Is this possible bending with the grain? Any tips? I've veneered flat surfaces in the past using contact cement (EvoSti...
1 comments posted 21yrs
posted by curried_pook
1 comments posted 21yrs posted by curried_pook

where to buy real chalkboard material?

I am looking to buy, preferable a real slate or maybe EZ Slate chalkboard material so I can incorporate it into a projec...
18 comments posted 21yrs
posted by noemail
18 comments posted 21yrs posted by noemail

Portable Miter Saw Stand

Hey Folks! I'm looking for a well made portable Miter Saw Stand, preferably with wheels, for under $300 What are your re...
12 comments posted 21yrs
posted by info
12 comments posted 21yrs posted by info

How to cut arborite in a corner???

I may have made a small mistake. I glued my arborite onto the counter top for some new cabinets and forgot that one sid...
4 comments posted 21yrs
posted by Seanold
4 comments posted 21yrs posted by Seanold

hardwood floor problem

So I'm about to put some hardwood floors (or laminate) in our laundry room, which is shaped like a rectangle with part...
4 comments posted 21yrs
posted by dpenney
4 comments posted 21yrs posted by dpenney

cutting questions

I'm about to build a big wraparound u shaped desk/hutch unit for my home office. I was making some test cuts out in the...
7 comments posted 21yrs
posted by mrneln
7 comments posted 21yrs posted by mrneln

Some nice finds at the swap meet

Found a new vendor at my local, monthly swap meet. Had a bunch of nice old stuff. Planes, chisels, braces, etc. Fair nu...
6 comments posted 21yrs
posted by johncyn
6 comments posted 21yrs posted by johncyn

router problem

A little help, please. I have a Crapsman router ( I know, but it wwas a gift {honest}. I have used it for a couple of y...
5 comments posted 21yrs
posted by bhoman1
5 comments posted 21yrs posted by bhoman1

installing hardwood flooring

Anybody know of any good sites with instructions on how to lay hardwood flooring. I've searched on Google and can find...
3 comments posted 21yrs
posted by scott.n.jill
3 comments posted 21yrs posted by scott.n.jill

Windsor chair spindles - best way to make?

Can anyone provide a better work method for producing Windsor chair spindles besides spokeshaving? A typical spindle wo...
8 comments posted 21yrs
posted by fdavidander
8 comments posted 21yrs posted by fdavidander

HELP! Difficulty changing table saw blade

I have a NEW general international table saw, and I'm finding it exceeding difficult to change the blade. The nut is wa...
15 comments posted 21yrs
posted by the_critic
15 comments posted 21yrs posted by the_critic