Woodworking Forum

  1. Home
  2. Woodworking Forum
51629 Threads Posts
to

Worth reading in Woodworking Forum

Resawing 12" heart pine

I asked a related question months earlier in this NG regarding hiring a portable bandmill to do this job, and the respo...
0 comments posted 21yrs
posted by brianc1959
0 comments posted 21yrs posted by brianc1959

Decking info

I am currently planning reworking a backyard deck and then screening it in. I have no experience in the synthetic decki...
7 comments posted 21yrs
posted by mextex1
7 comments posted 21yrs posted by mextex1

OT - Cabinet job opportunities

FYI My company is looking for experienced people in West Melbourne FL : Cabinet Makers / Countertop Fabricators $15.00/...
38 comments posted 21yrs
posted by rmo7hatespam
38 comments posted 21yrs posted by rmo7hatespam

FS: Pen turning stuff

Just found a whole box 12"x14"x6" full to the top with pen blanks, woods, pen kits, mandrels, drill bits, etc. under my...
1 comments posted 21yrs
posted by jimREMOVETHIS
1 comments posted 21yrs posted by jimREMOVETHIS

My new shop!

Hi Folks, Everyone is invited to see photos of my new shop: http://www.ts-aligner.com/ejbco.htmAnd, if you happen to be...
6 comments posted 21yrs
posted by ejb
6 comments posted 21yrs posted by ejb

Face Frames

Any reason why I should not just glue my faceframe to the carcase? The glue surface will be 2" frame on a 1.5" edge. Do...
4 comments posted 21yrs
posted by vgbaron
4 comments posted 21yrs posted by vgbaron

Spalted Maple

I have a piece of maple with very heavy spalting. It is rather soft in spots. Is there a way to stabilize the wood to ma...
7 comments posted 21yrs
posted by jgtr
7 comments posted 21yrs posted by jgtr

knife box

I need to make a carry box for some chefs knives (and a mandolin, but that is more straight forward). It (a) do not hav...
10 comments posted 21yrs
posted by usenet
10 comments posted 21yrs posted by usenet

Mobilizing a compressor?

Hi Folks, I've a PC pancake compressor; at 60ish pounds, it's certainly portable enough around the base^w shop, but it'...
17 comments posted 21yrs
posted by John.Thomas
17 comments posted 21yrs posted by John.Thomas

Unusual refinishing problem

About 30 years ago, my father-in-law had a table professionally refinished. It's a large solid oak dining room table, w...
7 comments posted 21yrs
posted by rjbonn
7 comments posted 21yrs posted by rjbonn

Spray Painting - Latex

Spray Painting Latex Primer on walls and ceiling etc... To be used later for finishing furniture... I will be buying a...
4 comments posted 21yrs
posted by willr
4 comments posted 21yrs posted by willr

Some bits not suitable for impact driver?

Hey All, I just got yesterday the Makita 14.4 kit that includes their impact driver (as well as drill/driver, and workl...
11 comments posted 21yrs
posted by www_recww
11 comments posted 21yrs posted by www_recww

Mystery blue-grey wood

Greetings: I recently bought a "box 'o veneer" at Lee Valley. I like to inlay small strips and curves into many of the...
10 comments posted 21yrs
posted by will.supply
10 comments posted 21yrs posted by will.supply

sanding question

Hello again guys.. Can someone go over proper use of sanding sponges? Specifically, how much pressure should be applied...
2 comments posted 21yrs
posted by e122176s
2 comments posted 21yrs posted by e122176s