Woodworking Forum

  1. Home
  2. Woodworking Forum
51629 Threads Posts
to

Worth reading in Woodworking Forum

Dust collector not collecting.

Why is it that the most obvious solution is always the one checked last? Dust collector not sucking, running but no suc...
11 comments posted 21yrs
posted by bryanberguson
11 comments posted 21yrs posted by bryanberguson

What size rounding bit for 3/4" stock?

If I want to create a rounded edge on a piece of 3/4" wood, what size router bit would I use? I want it to be smooth rou...
17 comments posted 21yrs
posted by jtpryan
17 comments posted 21yrs posted by jtpryan

Amazon shipped my Bessey's

I want to follow up on my comment about Bessey's on Amazon (Tool Crib) For those of you who may have to wait until Dece...
16 comments posted 21yrs
posted by spamhater113+U051017075933
16 comments posted 21yrs posted by spamhater113+U051017075933

All metric tape measure

Anyone know of a retractable tape measure that reads in metric on both sides of the blade?
8 comments posted 21yrs
posted by jhilson
8 comments posted 21yrs posted by jhilson

Shop Furniture Materials & Joinery

I'm betting that for most of us, the first four or five pieces of "furniture" we make are "shop furniture" - a router c...
2 comments posted 21yrs
posted by charlieb
2 comments posted 21yrs posted by charlieb

MAPLE STORAGE CABINET AND EASEL

http://www.popularmechanics.com/home_improvement/furniture/1318901.html Courtesy of what I think is possibly the best w...
0 comments posted 21yrs
posted by Jakofalltrades
0 comments posted 21yrs posted by Jakofalltrades

Rolling Pin Ball Bearings.....

Sorry folks for the simpleness of this question! I'm thinking of making around 20 or so rolling pins as Christmas prese...
16 comments posted 21yrs
posted by Nospam
16 comments posted 21yrs posted by Nospam

Kitchen cabinet design question

I'm looking to build wall cabinets for a kitchen with an 8' ceiling that go (essentially) all the way to the ceiling (i...
7 comments posted 21yrs
posted by toddrf
7 comments posted 21yrs posted by toddrf

Plywood in Northern NJ

I am curious if any one can reccomend a supplier (retail) for hardwood plywood in Northern NJ (Morris County)? Also I j...
4 comments posted 21yrs
posted by jhennings
4 comments posted 21yrs posted by jhennings

Did lots of machining this weekend *w/pics*

Hello Everyone, I got lots of machining done this weekend. In my never ending kitchen project, I started on 14 more doo...
4 comments posted 21yrs
posted by dfeisan
4 comments posted 21yrs posted by dfeisan

Eugene, Oregon. Thanks and a plug for Jerry's

My thanks to all who offered advice and help on woodworking places of interest in Eugene, Or. Due to the state of my da...
2 comments posted 21yrs
posted by mike72903
2 comments posted 21yrs posted by mike72903

What If George Bush's "Brain" Indicted?

If Karl Rove indicted by the Special Prosecutor can George Bush do anything right?
11 comments posted 21yrs
posted by jamesr
11 comments posted 21yrs posted by jamesr

Fine Woodworking... Not!

There was a bit of disruption a few streets over from last Wednesday to today (Sunday). Trading Spaces was in town shoo...
0 comments posted 21yrs
posted by grossboj.nospam
0 comments posted 21yrs posted by grossboj.nospam

compound miter question (crown molding)

Hi everyone, I'm trying to figure out if it is possible to cut crown molding so that it not only turns a 90 degree outs...
2 comments posted 21yrs
posted by nothanks
2 comments posted 21yrs posted by nothanks