Woodworking Forum

  1. Home
  2. Woodworking Forum
51629 Threads Posts
to

Worth reading in Woodworking Forum

WTD: Delta Rockwell Dust Door :-)

Ok, yea, its a long shot, but I picked up a 70's Rockwell Unisaw, sans its dust door. Anyone one have a spare kicking ab...
0 comments posted 20yrs
posted by escarcegaNOSPAM
0 comments posted 20yrs posted by escarcegaNOSPAM

WTD: Delta Saw Buck Handles

Picked up a later model Delta Sawbuck. Plastic handles broken. Vertical Handles., looked like the newer handles were ho...
0 comments posted 20yrs
posted by escarcegaNOSPAM
0 comments posted 20yrs posted by escarcegaNOSPAM

Old Delta Milwaukee Planer

Picked up and old Delta Milwaukee 13"x5" Planer today. Going to restore the old girl. Looks like a 22-101? Looks like t...
0 comments posted 20yrs
posted by escarcegaNOSPAM
0 comments posted 20yrs posted by escarcegaNOSPAM

cutting a spiral

Anybody have info on bandsawing a spiral? I can do one halfway decently by hand but perhaps there is a better way. expec...
0 comments posted 20yrs
posted by jo4hn
0 comments posted 20yrs posted by jo4hn

$100 rebate on Performax 16-32?

I see Amazon has a mfgs rebate on this. It it good for all dealers, or just "participating" dealers?
1 comments posted 20yrs
posted by Toller
1 comments posted 20yrs posted by Toller

High lacquered rosewood table-needs wax

someone replied about my deco 30's hi lacquered cocktail table and suggested cleaning with dish soap-etc then applying w...
0 comments posted 20yrs
posted by aljrnyc
0 comments posted 20yrs posted by aljrnyc

What Happened to Jesada?

When reading the earlier post about router bits I wondered what the status was with Jesada Tools. When I connected to t...
14 comments posted 20yrs
posted by frankdrack
14 comments posted 20yrs posted by frankdrack

Delta Model 36-717

Anyone have an opinion about this saw? Thanks, Mark
5 comments posted 20yrs
posted by mgreene93
5 comments posted 20yrs posted by mgreene93

Fu-Chest Design/Plans

Greets all. My wife wants me to build her a Fu-Chest. If you haven't heard of these before, they are pretty much just t...
0 comments posted 20yrs
posted by joseph
0 comments posted 20yrs posted by joseph

Fake Palm trees

Hello Group, Today I was asked by a freind to make three fake palm tree tops for them to decorate the tops of some stum...
2 comments posted 20yrs
posted by duckbite
2 comments posted 20yrs posted by duckbite

Pocket hole screws

I am planning to build a built in set of drawers using melamine MDF panels. Is this material suitable for use with the K...
5 comments posted 20yrs
posted by hodget
5 comments posted 20yrs posted by hodget

Finishing Question

Hi All, I'm finishing a walnut box with an oil/urethane top coat, satin, using a rag, then 0000 steel wool. It looks gr...
6 comments posted 20yrs
posted by cwo4cno7325
6 comments posted 20yrs posted by cwo4cno7325

Lacquer Finishing Advice Needed

This sounds a little strange (even to me) but here goes. I have a fireplace mantel that is coated with a pigmented lacq...
3 comments posted 20yrs
posted by dougkosty
3 comments posted 20yrs posted by dougkosty

What I want for Christmas - General toys on sale

I went to my local Beaver Lumber/Home Hardware store today. While doing my customary obeisance to the General 350 and s...
3 comments posted 20yrs
posted by recnorm
3 comments posted 20yrs posted by recnorm

Two man whip saw?

Maybe a little OT for here, but worth a try. How can I tell a rip from a crosscut whip saw? I've come across a two-pers...
5 comments posted 20yrs
posted by gigabitbucket
5 comments posted 20yrs posted by gigabitbucket