Woodworking Forum

  1. Home
  2. Woodworking Forum
51629 Threads Posts
to

Worth reading in Woodworking Forum

LeeValley catalog cover

Ok, I give up. What the hell is that thing on the cover of the 2005-06 Lee Valley woodworking tool catalog? The ivory/ca...
6 comments posted 20yrs
posted by jbarta
6 comments posted 20yrs posted by jbarta

Problem with Stihl 041 AV

Recently got this saw(my first) and I had it running but it would not idle. I adjusted the low speed screw but was a li...
1 comments posted 20yrs
posted by etiennepb
1 comments posted 20yrs posted by etiennepb

Woodworking clubs and information exchange

This may seem like spam but it really isn't. I belong to the cincinnati woodworking club and we video tape our meetings...
0 comments posted 20yrs
posted by larryhab
0 comments posted 20yrs posted by larryhab

shopsmith parts FS

While cleaning out a box of junk I found the following Shop Smith Model X parts: Three sets of shaper heads One set for...
2 comments posted 20yrs
posted by currancopeland
2 comments posted 20yrs posted by currancopeland

Craftsman jointer.

I have this Craftsman jointer: http://www6.sears.ca/webapp/wcs/stores/servlet/ProductDisplay?categoryId=32280&catalogId...
4 comments posted 20yrs
posted by aaa
4 comments posted 20yrs posted by aaa

Tough one

I was handed down a 4/1/2 Montgomery Wards Model 15fd250 Jointer. I am 65 so this is old. Works like new, and I use it...
4 comments posted 20yrs
posted by Nonameooo
4 comments posted 20yrs posted by Nonameooo

Finally finished something.

Long time lurker, first time poster. (try not to be too harsh) http://woodblog.sitestrong.com/Mike
24 comments posted 20yrs
posted by killermike
24 comments posted 20yrs posted by killermike

FRAC = DEC

Inches: Fraction Decimal Value 1/64 0.015625 1/32 0.03125 3/64 0.046875 1/16 0.0625 5/64 0.078125 3/32 0.09375 7/64 0.1...
0 comments posted 20yrs
posted by ahem
0 comments posted 20yrs posted by ahem

Dream Router Table

I went out to my shop this morning to find that a couple of 2x8s that had been leaning up against the wall for weeks no...
10 comments posted 20yrs
posted by BrianL.Henderson
10 comments posted 20yrs posted by BrianL.Henderson

Ratchet multi-position handle - 1/4-20

I am looking for a source for handles like item I on http://www.woodcraft.com/family.aspx?FamilyID=1072Woodcraft only s...
2 comments posted 20yrs
posted by spitz
2 comments posted 20yrs posted by spitz

Repair my Emglo AM78-HV4V air compressor

We were using our Emglo and shut it down for a lunch break. When we came back and tried to start it again all we got wa...
22 comments posted 20yrs
posted by no
22 comments posted 20yrs posted by no

Palmgren 84929/Craftsman 6" jointer knive removal

I have a Palmgren 84261 jointer, same as Craftsman 6 1/8" benchtop jointer, its about 4 months old. Am trying to remove...
0 comments posted 20yrs
posted by joe_cotter
0 comments posted 20yrs posted by joe_cotter

Cutlist plus - how to activate?

Hey all, Based on the large number of positive comments on this newsgroup and a need to do are fair number of cabinet p...
10 comments posted 20yrs
posted by dhenze
10 comments posted 20yrs posted by dhenze

Super Shop Lathe?

I saw an ad for a used Supershop wood lathe. The owner says it's a model 13455. I spent some time Googling and can only...
2 comments posted 20yrs
posted by jjinatxBOB
2 comments posted 20yrs posted by jjinatxBOB