Latest threads in Woodworking Forumshow only best voted threads
| Subject | Author | Posted | Replies | |
|---|---|---|---|---|
|
|
Is it worth a career change? Part 2
I appreciate all the advice and insight I got on the original posting called "Is it worth a career change?" But let's suppose I'm either dumb or stubborn or both and wanted to open up a business...
23
|
17 years ago
|
23 | |
|
|
Pool Table Plans (Free)
Here is a link to my pool table project. I put it back up after taking it down for a while. They are free and have some good ideas. Enjoy... Christmas http://pooltable.kirchelconsulting.comMerry
—
|
17 years ago
|
— | |
|
|
Any 240v woodworking equipment need a neutral?
Is it fair to say that all 240v woodworking equipment runs without neutrals? I am running a new circuit and would prefer to use 10/2 rather than 10/3; but sure don't want to do it twice.
142
|
17 years ago
|
142 | |
|
|
Veneer on a plane
I was watching this TV show about these high end custom business jets. The thing that struck me was the unbelievable veneer work on the cabinetry. Of course it was wonderful crotch and burl species...
4
|
17 years ago
|
4 | |
|
|
Damaging a counter when cutting the 45 degree of an "L" shaped countertop...
Hi all, Yesterday I tried to put the new melamine countertop (Kober) to my kitchen with awful results: I should buy a new one and redo everything. The principal problem was to cut the 45degree to make...
14
|
17 years ago
|
14 | |
|
|
Black & Decker RP200 Edge Guide?
I'm trying to locate an edge guide for the Black & Decker RP200 router. Black & Decker lists it as a discontinued accessory. Does anyone know of an edge guuide from another router manufacturer...
—
|
17 years ago
|
— | |
|
|
advice/article on filling worm holes in walnut
I've done several searches, but I can't seem to find an article for filling worm holes in walnut. I've a large chunk of crotch walnut that I want to use as the support block in my Klausz-inspired...
5
|
17 years ago
|
5 | |
|
|
Dumb Drill Press Question
I just purchased my first drill press (Delta 12" benchtop DP-300L). I'm not totally new to drill presses as I used to fool around with my dad's when I was a kid. Having never assembled one before, I...
14
|
17 years ago
|
14 | |
|
|
Planer alignment driving me insane
I have been working on a custom cutting board for SWMBO for the last 2 weeks (roughly 2 hours per week) and have found after planing some small parts that my Delta JT160 is out of alignment. I thought...
6
|
17 years ago
|
6 | |
|
|
Radial Arm Saw Chipping
This newsgroup has been a great help to me. I sincerely appreciate the helpful and courteous responses that I have received to my few, but important previous posts. I remember seeing this addressed in...
10
|
17 years ago
|
10 | |
|
|
OT: Swingman, try this one
Karl: Try Just take out "the garbage" and the "spam". Thanks - looking forward to hearing from you. Robert
1
|
17 years ago
|
1 | |
|
|
Why Should We Thin Poly Before Rubbing the Finish?
I am reading info on rubbing finish. There is one thing that I don't quite understand. The instruction indicates that we should thin the finish, let it hardened, and then rub the finish. This...
8
|
17 years ago
|
8 | |
|
|
Pitch Remover?
What does everyone use to get pitch off sawblades and router bits? How well does it work? TIA David Starr
17
|
17 years ago
|
17 | |
|
|
Cost of Jet Knives
What gives? JET 16" planer knives (set of 3) have gone from $94 (US) to $154! Add to that the problem of resharpening them. Jet wants the primary grind at 40 degrees and secondary bevel at 42. The...
11
|
17 years ago
|
11 | |
|
|
links needed for compartmentalizing m/c screw lengths
At my home general work area I have plastic tins of fasteners of all types. When I need something I dump it out into a flat bottomed rectangular bucket. I can them as multiple sizes of wood screws,...
2
|
17 years ago
|
2 |