O/T: Tractor Square Dancing

Oh, yeah! I've seen more than one turn turtle, even with wide front end. The operator still has to be smarter than the machine!

The A could be very vicious in that respect, with the engine on the left. Had to "think" before doing sidehill work.

As I said in my first post, the narrow front end was easier to maneuver in tight quarters, but was a PITA for some work. Uncle firmly believed in narrow FE after getting first C, and couldn't shake him, even after he got a 2nd C that came with both. Tried to talk him into installing the WFE, but he wouldn't hear of it until after cousin took over the farm and got (I believe) a Farmall 460 with WFE, and after Uncle worked with it helping out, couldn't get him away from the WFE.

Norm

Nahmie wrote: ...

I actually did think of one reason for them -- probably were somewhat less expensive which may have been a bigger difference back then...

What are them "tight quarters" of which thee speak??? :)

If there isn't at least a full 80, we feel constrained out here... :)

Our progression went from original Twin City 10-20 (steel wheel monster) to a period w/ several Cat 22's. Used them for row crop in particular w/ 3-row pull-type JD lister and cultivator. Terrible in the sandy soil and cross wind to have to sit there and take the dirt the tracks carried but great for following the rows. First Farmall's were the M's, then

400 and a 560. About the time of the 400 granddad bought a little Allis WD-45 since he wanted to keep doing field work but was where the larger were getting hard for him to handle. Full line of the "Snap-Coupler" tool bar equipment with it. Had so much invested in the equipment eventually bought a D17 that I put in thousands of hours on doing row crop work w/ 4-row lister/knife sled/cultivator to lay by with.

About same time got the Case 930 flatland -- our first large (90(?) hp) tractor--brother did most of the flat land work 'cuz he didn't like having to keep straight rows so much while I was bored w/o the concentration require but only go 'round 'n 'round the square... :)

The 560 didn't hold up well and was the last IH--it got replaced by the first JD--a 4010 row crop and our first diesel. Out here virtually everybody used LP thru the 50s/60s and into the 70s. Then the progression to larger equipment really began -- the 4010 morphed into

4230, 4440, 4640 ending up w/ the 8000 series now.

Meanwhile, equipment went from 14-ft single one-way to 3 ganged

15-ft'ers to 30-ft chisels and sweeps. Planters went from 4 to 6 to 8-row listers to 12 and 16-row planters w/ air seeders and GPS guidance. Now may only cultivate once before planting if at all; almost everything is low- or minimum-till practice instead to aid in moisture conservation and to minimize wind erosion.

Can't leave out the harvesting changes, either--from old header/binder/stationary thresher to 10- or 12-ft pull-type Gleaner to the "huge" 14-ft Case (also puller) which required three/four operators plus the tractor man then the first self-propelled--a Massey-Harris altho don't recall model--the 90 was second if remember correctly. Now they're also up to a "modest" 32-ft header since some of our ground does have a little swell in it, it's hard to use the really large machines they do some places since the dryland wheat may not get very tall every (most?) year. Like the planters, they now include all sorts of gizmos--yield monitoring and moisture measurement tied into GPS for automagically feeding back into seeding rate and fertilization blending/amounts for subsequent years reflecting local soil conditions within a particular field. GPS w/ autosteer on spray rigs (90-ft booms) maintain about 2" accuracy and regulate output based on ground speed and location on a several-nozzle individually regulated control system granularity.

Much more different... :)

--