Latest threads in Woodworking Forumshow only best voted threads
Subject | Author | Posted | Replies | |
---|---|---|---|---|
|
Finger Board Tricks?
If you've read m other post I need to make a double sided finger board at least 25" long. In this case it means a ton of cuts. I was wondering if anyone had any ideas for evenly spacing all of the...
15
|
17 years ago
|
15 | |
|
Cutting 4" Boards down to 2"
My table saw is too small to rip the boards up the middle and my bandsaw is too small any ideas folks?
10
|
17 years ago
|
10 | |
|
Should I use mineral spirits after sanding between polyurethane coats (2023 Update)
The first application of polyurethane finally dried on my red oak baseboard. I sanded the baseboard and used a tacky cloth to remove the dust. Should I wipe down the baseboard with a rag dipped in...
14
|
17 years ago
|
14 | |
|
Finish before or after installing hinges
I am just finishing up a small pine step stool that has a little storage compartment. I am going to use two brass butt hinges for the lid. Would you apply the finish before attaching the hinges or...
2
|
17 years ago
|
2 | |
|
Ridgid table saw
I'm thinking about getting a Ridgid table saw. I recently moved from Northern VA to Maine and gave my son all my stationary ww tools (Delta and Jet). Anybody out there using a Ridgid? Any problems or...
8
|
17 years ago
|
8 | |
|
Router plane vs Plough plane
Hi all! I have a doubt about this kind of planes... tried to search on the groups, but didn't find much (sorry If I'm asking the same again). What would be the practical difference between a plough...
1
|
17 years ago
|
1 | |
|
Saddam's cat
http://tinypic.com/view/?pic=2hrk8qt
2
|
17 years ago
|
2 | |
|
DeVilbiss recall: affects compressors and pwr washers
Don't know if you guys have heard but I got a notice from Amazon late yesterday regarding the recall. It affects my PC mobile air compressor. Defective item is plastic wheel hubs. Here is the link to...
2
|
17 years ago
|
2 | |
|
Hand Plane Square Beam Stock
Hi, I'm hand planing Maple post/beams from hardwood pallets I get from work. The beams are rough sawn approximately four by four inches. With the rough surface removed the wood is as good as I could...
6
|
17 years ago
|
6 | |
|
Stanley Tripod Flashlight
Any body got one of these? I received the Stanley Tripod Flashlight (model 95-112) as a late holiday president and fired it up yesterday for the first time. It has 6 LED bulbs and uses up to 9 AA...
60
|
17 years ago
|
60 | |
|
Re: Compulsive Hoarding....Do You Know Someone LIke This?
Not a problem in my case- every 3-6 months, I rent a two yard dumpster, and anything that I haven't used since I rented the last one either goes in there, or is given away or sold if it is something...
6
|
17 years ago
|
6 | |
|
WORKSTATION
I do not have the huge amount of faith needed to be an Atheist. http://mysite.verizon.net/homestudioguy/id18.html
—
|
17 years ago
|
— | |
|
A Couple Of Warm Fuzzies
Well, was in the midst of making a new saw sled, then found out my little saw wasn't keeping its alignment. It still cuts well enough, but winds up with about a 1/4" kerf, instead of 1/8". Not really...
12
|
17 years ago
|
12 | |
|
snip and a Ryobi planer
I got the Ryobi 13" planer and it snips fairly bad, it didn't come with any infeed/out feed tables, my question is how big do I build them, 13" wide obviusely, but how long 13", 15", 17" etc or is it...
3
|
17 years ago
|
3 | |
|
This here place...
For you "Almost Live" fans...
4
|
17 years ago
|
4 |