Woodworking Forum

51629 Threads Posts
to

Fine Woodworking Magazines #1-124

I previously advertised these here and did not find a buyer. Will try once more to offer these to the woodworking commu...
0 comments posted 22yrs
posted by bobster47
0 comments posted 22yrs posted by bobster47

Bandsaw purchase

I am considering the purchase of an 18" bandsaw for both resawing and cutting moderately sharp curves. Knowing I can get...
9 comments posted 22yrs
posted by Clif
9 comments posted 22yrs posted by Clif

Butsudan help needed

Hi Everyone, I've been asked by a couple of friends if I would make a Butsudan (A Buddhist altar) for them. I've done a...
5 comments posted 22yrs
posted by m.stanford3
5 comments posted 22yrs posted by m.stanford3

Ryobi 12-5/16 (AP-12) Planer Blades

My old Ryobi AP-12 surface planer is doing fine but showing signs of needing blade replacement and I'm getting nervous....
2 comments posted 22yrs
posted by rbrogan
2 comments posted 22yrs posted by rbrogan

dw621 spring removal

No instructions in the manual. How do I remove the sping in larger column? I want to use it in a table and can't figure...
0 comments posted 22yrs
posted by wworker
0 comments posted 22yrs posted by wworker

[OT] What Grows in My Garden

...just had to share this with you all. If you don't recognize it, it's called a stinkhorn mushroom(Phallus impudicus)....
11 comments posted 22yrs
posted by llhote
11 comments posted 22yrs posted by llhote

Tables on Framing Square

I finally replaced my trusty, rusty framing square with one of those yellow on black aluminum Stanley contractor specia...
2 comments posted 22yrs
posted by jim
2 comments posted 22yrs posted by jim

Re: Pear Wood - Who’da Thunk It?

> Wonder what prune wood is > >like? > > Kind of like raisin wood. Naw that would be more like grape wood.
0 comments posted 22yrs
posted by removespamlcb11211
0 comments posted 22yrs posted by removespamlcb11211

Aquarium Stand

I was considering building a stand for a new 75 gallon tank and I've got a few questions. I'm not so concerned about th...
10 comments posted 22yrs
posted by me7
10 comments posted 22yrs posted by me7

Jointing boards with a router

I have a router setup similar to that from the Router Workshop with the infeed side of the fence 3 mm less the outfeed....
8 comments posted 22yrs
posted by garryjcspamno
8 comments posted 22yrs posted by garryjcspamno

Linux users, problems connecting to LV?

Greetings, I've just had a very nice letter from LV customer service. Great response, but they couldn't help. I can't g...
12 comments posted 22yrs
posted by nospam
12 comments posted 22yrs posted by nospam

How to make > 45 degree cut

Every once in a while I find the need to make a cross cut that is greater than 45 degrees. The only way that I have fel...
4 comments posted 22yrs
posted by georgebravo2004
4 comments posted 22yrs posted by georgebravo2004

Fisch Workbench

Anyone seen one of these? Where I live you could hardly buy the wood for that price. Then again it wouldn't be "Malaysi...
2 comments posted 22yrs
posted by ppridday
2 comments posted 22yrs posted by ppridday

on big FAT lot o' tools!

eBay: 4317663947 ain't me... Alex
1 comments posted 22yrs
posted by ahem
1 comments posted 22yrs posted by ahem